Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseSteel AISI 4340 · Young's modulus (stiffness): MIL-HDBK-5J design value (AISI 4340, quenched and tempered)Steel AISI 4340 · Poisson's ratio: MIL-HDBK-5J design value (AISI 4340, quenched and tempered)
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyFDM Polycarbonate · Poisson's ratio: base material: polycarbonate family typical (Covestro Part and Mold Design guide, Table 3-1)
5
Makrolon 2405 Technical Data SheetCovestroFDM Polycarbonate · Thermal conductivity: base material: Covestro Makrolon 2405 injection-molding PC, typical, through-plane, 23 °CFDM Polycarbonate · Thermal expansion: base material: Covestro Makrolon 2405 injection-molding PC, typical, 23-55 °C, parallel
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM Polycarbonate is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM Polycarbonate stronger than Steel AISI 4340?
Steel AISI 4340 is stronger: its yield strength is 1,035 MPa against 53.3 MPa for FDM Polycarbonate (19.4x).
Which is lighter, FDM Polycarbonate or Steel AISI 4340?
FDM Polycarbonate is lighter: 1,190 kg/m³ against 7,840 kg/m³ for Steel AISI 4340.
Which is stiffer, FDM Polycarbonate or Steel AISI 4340?
Steel AISI 4340 is stiffer: Young's modulus 200 GPa against 2.39 GPa for FDM Polycarbonate, so the same part in Steel AISI 4340 deflects less under the same load.
Which is lighter for the same job, FDM Polycarbonate or Steel AISI 4340?
For the same stiffness or strength: FDM Polycarbonate is lighter for a stiff panel or plate, strong panel or plate; Steel AISI 4340 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
FDM Polycarbonate
Steel AISI 4340
Stiff rod or tie (tension)
12.7x heavier
lighter
Stiff beam (bending)
39% heavier
lighter
Stiff panel or plate
lighter
1.51x heavier
Strong rod or tie
2.95x heavier
lighter
Strong beam
10% heavier
lighter
Strong panel or plate
lighter
50% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM Polycarbonate or Steel AISI 4340?
Steel AISI 4340 stretches further before it breaks: 18% elongation at break against 9.2% for FDM Polycarbonate.
Thermal
Which conducts heat better, FDM Polycarbonate or Steel AISI 4340?
Steel AISI 4340 conducts heat better: 37.5 W/m·K against 0.2 W/m·K for FDM Polycarbonate.
Which expands less with temperature?
Steel AISI 4340 expands less: 11.3 µm/m·K against 65 µm/m·K for FDM Polycarbonate.