Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Ultimaker PC Technical Data Sheet, v5.00UltiMakerarchived copyFDM Polycarbonate · Yield strength: typicalFDM Polycarbonate · Ultimate tensile strength: typical, peak stress (= stress at yield)FDM Polycarbonate · Flexural strength: typicalFDM Polycarbonate · Elongation at break: typicalFDM Polycarbonate · Young's modulus (stiffness): typicalFDM Polycarbonate · Density: rangeFDM Polycarbonate · Glass transition: typicalFDM Polycarbonate · Max service temperature: HDT 0.455 MPa (printed specimens)
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyFDM Polycarbonate · Poisson's ratio: base material: polycarbonate family typical (Covestro Part and Mold Design guide, Table 3-1)
5
Makrolon 2405 Technical Data SheetCovestroFDM Polycarbonate · Thermal conductivity: base material: Covestro Makrolon 2405 injection-molding PC, typical, through-plane, 23 °CFDM Polycarbonate · Thermal expansion: base material: Covestro Makrolon 2405 injection-molding PC, typical, 23-55 °C, parallel
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM Polycarbonate is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM Polycarbonate stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 53.3 MPa for FDM Polycarbonate (16.6x).
Which is lighter, FDM Polycarbonate or Titanium?
FDM Polycarbonate is lighter: 1,190 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, FDM Polycarbonate or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 2.39 GPa for FDM Polycarbonate, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, FDM Polycarbonate or Titanium?
For the same stiffness or strength: FDM Polycarbonate is lighter for a stiff panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM Polycarbonate
Titanium
Stiff rod or tie (tension)
12.8x heavier
lighter
Stiff beam (bending)
1.86x heavier
lighter
Stiff panel or plate
lighter
3% heavier
Strong rod or tie
4.46x heavier
lighter
Strong beam
1.75x heavier
lighter
Strong panel or plate
9% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM Polycarbonate or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 9.2% for FDM Polycarbonate.
Thermal
Which conducts heat better, FDM Polycarbonate or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.2 W/m·K for FDM Polycarbonate.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 65 µm/m·K for FDM Polycarbonate.