Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA sample part to run stress or thermal on, free in your browser
Technical Bulletin ATS-129: Properties of Soda-Lime Silica Float Glass (2025)Pilkington North Americaarchived copyGlass · Ultimate tensile strength: typical mean surface tensile stress at fracture (MOR), 60 s load, weathered, 50% breakage probabilityGlass · Flexural strength: mean MOR (same value as tensile)Glass · Young's modulus (stiffness): typicalGlass · Density: typicalGlass · Poisson's ratio: typicalGlass · Thermal conductivity: typical at 75 FGlass · Thermal expansion: typical, 75-575 FGlass · Specific heat: typical at 75 FGlass · Max service temperature: strain point (ASTM C336) - stress-relaxation onset, not a rated service limit
3
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
4
Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Glass stronger than Plastic Nylon?
Plastic Nylon is stronger: its yield strength is 63.1 MPa against tensile strength 41 MPa for Glass (1.54x).
Which is lighter, Glass or Plastic Nylon?
Plastic Nylon is lighter: 1,140 kg/m³ against 2,500 kg/m³ for Glass.
Which is stiffer, Glass or Plastic Nylon?
Glass is stiffer: Young's modulus 72 GPa against 2.33 GPa for Plastic Nylon, so the same part in Glass deflects less under the same load.
Which is lighter for the same job, Glass or Plastic Nylon?
For the same stiffness or strength: Glass is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate; Plastic Nylon is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
Glass
Plastic Nylon
Stiff rod or tie (tension)
lighter
14.1x heavier
Stiff beam (bending)
lighter
2.53x heavier
Stiff panel or plate
lighter
43% heavier
Strong rod or tie
3.38x heavier
lighter
Strong beam
2.92x heavier
lighter
Strong panel or plate
2.72x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Glass or Plastic Nylon?
Glass conducts heat better: 0.937 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Glass expands less: 8.3 µm/m·K against 100 µm/m·K for Plastic Nylon.