Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, UltiMaker, National Institute of Standards and Technology, Eastman
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
Plastic PETG
Ultimaker PETG, 3D-printed specimens, XY (flat); Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v1.00, April 29, 2022.
1
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
4
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Iron stronger than Plastic PETG?
Iron is stronger: its yield strength is 186 MPa against 46.2 MPa for Plastic PETG (4.03x).
Which is lighter, Iron or Plastic PETG?
Plastic PETG is lighter: 1,270 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Iron or Plastic PETG?
Iron is stiffer: Young's modulus 207 GPa against 1.94 GPa for Plastic PETG, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Iron or Plastic PETG?
For the same stiffness or strength: Iron is lighter for a stiff rod or tie (tension), stiff beam (bending); Plastic PETG is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Iron
Plastic PETG
Stiff rod or tie (tension)
lighter
17.2x heavier
Stiff beam (bending)
lighter
1.67x heavier
Stiff panel or plate
30% heavier
lighter
Strong rod or tie
1.54x heavier
lighter
Strong beam
2.45x heavier
lighter
Strong panel or plate
3.08x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Iron or Plastic PETG?
Iron stretches further before it breaks: 38% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Iron or Plastic PETG?
Iron conducts heat better: 73.2 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 51 µm/m·K for Plastic PETG.