Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: BASF, ATI, Covestro, Steel Construction Institute
Plastic Nylon PA66
BASF Ultramid A3K (PA66, unreinforced injection-moulding grade), Product Information 02/2026, dry values (ISO methods)
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
3
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA66 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 316 · Poisson's ratio: design value (structural stainless steels)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Nylon PA66 stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against 85 MPa for Plastic Nylon PA66 (3.12x).
Which is lighter, Plastic Nylon PA66 or Stainless Steel 316?
Plastic Nylon PA66 is lighter: 1,130 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, Plastic Nylon PA66 or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 3 GPa for Plastic Nylon PA66, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, Plastic Nylon PA66 or Stainless Steel 316?
For the same stiffness or strength: Plastic Nylon PA66 is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic Nylon PA66
Stainless Steel 316
Stiff rod or tie (tension)
9.38x heavier
lighter
Stiff beam (bending)
15% heavier
lighter
Stiff panel or plate
lighter
1.75x heavier
Strong rod or tie
lighter
2.28x heavier
Strong beam
lighter
3.33x heavier
Strong panel or plate
lighter
4.02x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic Nylon PA66 or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 30% for Plastic Nylon PA66.
Thermal
Which conducts heat better, Plastic Nylon PA66 or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.33 W/m·K for Plastic Nylon PA66.
Which expands less with temperature?
Stainless Steel 316 expands less: 16.5 µm/m·K against 98 µm/m·K for Plastic Nylon PA66.