Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
5
Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic Nylon stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 63.1 MPa for Plastic Nylon (14x).
Which is lighter, Plastic Nylon or Titanium?
Plastic Nylon is lighter: 1,140 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic Nylon or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 2.33 GPa for Plastic Nylon, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic Nylon or Titanium?
For the same stiffness or strength: Plastic Nylon is lighter for a stiff panel or plate, strong panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
Plastic Nylon
Titanium
Stiff rod or tie (tension)
12.6x heavier
lighter
Stiff beam (bending)
1.8x heavier
lighter
Stiff panel or plate
lighter
6% heavier
Strong rod or tie
3.61x heavier
lighter
Strong beam
50% heavier
lighter
Strong panel or plate
lighter
4% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Plastic Nylon or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 100 µm/m·K for Plastic Nylon.