Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
5
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic PEEK stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 98 MPa for Plastic PEEK (9.03x).
Which is lighter, Plastic PEEK or Titanium?
Plastic PEEK is lighter: 1,300 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic PEEK or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 4 GPa for Plastic PEEK, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic PEEK or Titanium?
For the same stiffness or strength: Plastic PEEK is lighter for a stiff panel or plate, strong panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
Plastic PEEK
Titanium
Stiff rod or tie (tension)
8.4x heavier
lighter
Stiff beam (bending)
1.57x heavier
lighter
Stiff panel or plate
lighter
11% heavier
Strong rod or tie
2.65x heavier
lighter
Strong beam
27% heavier
lighter
Strong panel or plate
lighter
13% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PEEK or Titanium?
Plastic PEEK stretches further before it breaks: 25% elongation at break against 16% for Titanium.
Thermal
Which handles higher temperatures, Plastic PEEK or Titanium?
Titanium does: 400 °C against 240 °C for Plastic PEEK.
Which conducts heat better, Plastic PEEK or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 55 µm/m·K for Plastic PEEK.