Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
4
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic PETG stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against 46.2 MPa for Plastic PETG (19.2x).
Which is lighter, Plastic PETG or Titanium?
Plastic PETG is lighter: 1,270 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, Plastic PETG or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 1.94 GPa for Plastic PETG, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, Plastic PETG or Titanium?
For the same stiffness or strength: Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Plastic PETG
Titanium
Stiff rod or tie (tension)
16.9x heavier
lighter
Stiff beam (bending)
2.2x heavier
lighter
Stiff panel or plate
12% heavier
lighter
Strong rod or tie
5.49x heavier
lighter
Strong beam
2.05x heavier
lighter
Strong panel or plate
25% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PETG or Titanium?
Titanium stretches further before it breaks: 16% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Plastic PETG or Titanium?
Titanium conducts heat better: 6.6 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Titanium expands less: 9 µm/m·K against 51 µm/m·K for Plastic PETG.