Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: UltiMaker, ATI, Steel Construction Institute, NatureWorks
Plastic PLA
Ultimaker PLA, 3D-printed specimens, XY (flat) orientation; Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS dated April 20, 2022.
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
3
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 316 · Poisson's ratio: design value (structural stainless steels)
4
Engineering Properties of Ingeo BiopolymerNatureWorksarchived copyPlastic PLA · Thermal conductivity: base material: NatureWorks Ingeo biopolymer, amorphous sheet, 25 °CPlastic PLA · Specific heat: base material: NatureWorks Ingeo biopolymer, amorphous sheet, 25 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PLA is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic PLA stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against 52.5 MPa for Plastic PLA (5.05x).
Which is lighter, Plastic PLA or Stainless Steel 316?
Plastic PLA is lighter: 1,240 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, Plastic PLA or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 3.25 GPa for Plastic PLA, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, Plastic PLA or Stainless Steel 316?
For the same stiffness or strength: Plastic PLA is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic PLA
Stainless Steel 316
Stiff rod or tie (tension)
9.51x heavier
lighter
Stiff beam (bending)
21% heavier
lighter
Stiff panel or plate
lighter
1.64x heavier
Strong rod or tie
lighter
28% heavier
Strong beam
lighter
2.2x heavier
Strong panel or plate
lighter
2.88x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PLA or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 7.8% for Plastic PLA.
Thermal
Which conducts heat better, Plastic PLA or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.13 W/m·K for Plastic PLA.