Materials / Compare
Plastic Polycarbonate vs. Stainless Steel 17-4PH
Compare Plastic Polycarbonate vs. Stainless Steel 17-4PH strength, stiffness, weight and thermal properties.
| Mechanical | Plastic Polycarbonate | Stainless Steel 17-4PH |
|---|---|---|
| Yield strength | 65MPa1 | 1,275MPa219.6x stronger |
| Ultimate tensile strength | 65MPa1 | 1,379MPa2 |
| Flexural strength | 97MPa1 | not sourced |
| Elongation at break | 125%113.9x more ductile | 9%2 |
| Young's modulus (stiffness) | 2.4GPa1 | H 900197GPa282.1x stiffer |
| Density | 1,200kg/m³16.5x lighter | H 9007,800kg/m³2 |
| Strength to weight | 54.2kN·m/kg | 163kN·m/kg3.02x higher |
| Stiffness to weight | 2MN·m/kg | 25.3MN·m/kg12.6x higher |
| Poisson's ratio | 0.383 | H 9000.2722 |
| Shear modulus | 0.87GPa | 77.4GPa89.1x stiffer in shear |
| Bulk modulus | 3.33GPa | 144GPa43.2x higher |
| Speed of sound | 1,414m/s | 5,026m/s3.55x faster |
| Thermal | Plastic Polycarbonate | Stainless Steel 17-4PH |
|---|---|---|
| Thermal conductivity | 0.2W/m·K1 | at 149 °C17.9W/m·K289.5x more heat through a fin |
| Thermal expansion | 65µm/m·K1 | mean10.8µm/m·K26.02x less |
| 100 mm part over a 50 °C swing | 325µm growth | 54µm growth6.02x less |
| Specific heat | 1,172J/kg·K42.55x higher | mean460J/kg·K2 |
| Heats up and cools (diffusivity) | 0.142mm²/s | 4.99mm²/s35.1x faster |
| Thermal shock resistance | 51.7W/m | 7,809W/m151x more resistant |
| Glass transition | 144°C1 | not sourced |
| Max service temperature | UL 746B RTI125°C1 | 316°C2191 °C hotter |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources4 documents: Covestro, Cleveland-Cliffs, Bayer MaterialScience
- Plastic Polycarbonate
- Covestro Makrolon 2405 general-purpose PC (MVR 19), Covestro technical datasheet version 2026-09-28, typical values
- Stainless Steel 17-4PH
- Cleveland-Cliffs 17-4 PH, Condition H 900, sheet/strip, transverse (Product Data Bulletin, May 2021)
- 1Makrolon 2405 Technical Data SheetCovestroPlastic Polycarbonate · Yield strength: typical, tensile yieldPlastic Polycarbonate · Ultimate tensile strength: typical, stress at breakPlastic Polycarbonate · Flexural strength: typical, flexural strengthPlastic Polycarbonate · Elongation at break: typical, strain at breakPlastic Polycarbonate · Young's modulus (stiffness): typicalPlastic Polycarbonate · Density: typicalPlastic Polycarbonate · Thermal conductivity: typical, through-plane, 23 CPlastic Polycarbonate · Thermal expansion: typical, 23-55 C, parallel and normalPlastic Polycarbonate · Glass transition: typical, DSC 10 C/minPlastic Polycarbonate · Max service temperature: UL 746B RTI, tensile strength, 1.5 mm
- 217-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 17-4PH · Yield strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Ultimate tensile strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Elongation at break: typical, transverse, in 2 in. (50.8 mm)Stainless Steel 17-4PH · Young's modulus (stiffness): H 900Stainless Steel 17-4PH · Density: H 900Stainless Steel 17-4PH · Poisson's ratio: H 900 (column)Stainless Steel 17-4PH · Thermal conductivity: at 149 °C (300 °F), H 900Stainless Steel 17-4PH · Thermal expansion: mean, 21–93 °C (70–200 °F), H 900Stainless Steel 17-4PH · Specific heat: mean, 0–100 °C, H 900Stainless Steel 17-4PH · Max service temperature: strength-retention limit (not oxidation)
- 3Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic Polycarbonate · Poisson's ratio: typical, polycarbonate family (Covestro Part and Mold Design guide, Table 3-1)
- 4Makrolon 2405 Data Sheet, ASTM valuesBayer MaterialSciencearchived copyPlastic Polycarbonate · Specific heat: typical (guide value), Bayer ASTM datasheet for Makrolon 2405, ASTM D 2766
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic Polycarbonate stronger than Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stronger: its yield strength is 1,275 MPa against 65 MPa for Plastic Polycarbonate (19.6x).
Which is lighter, Plastic Polycarbonate or Stainless Steel 17-4PH?
Plastic Polycarbonate is lighter: 1,200 kg/m³ against 7,800 kg/m³ for Stainless Steel 17-4PH.
Which is stiffer, Plastic Polycarbonate or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stiffer: Young's modulus 197 GPa against 2.4 GPa for Plastic Polycarbonate, so the same part in Stainless Steel 17-4PH deflects less under the same load.
Which is lighter for the same job, Plastic Polycarbonate or Stainless Steel 17-4PH?
For the same stiffness or strength: Plastic Polycarbonate is lighter for a stiff panel or plate, strong panel or plate; Stainless Steel 17-4PH is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
| Part that must be | Plastic Polycarbonate | Stainless Steel 17-4PH |
|---|---|---|
| Stiff rod or tie (tension) | 12.6x heavier | lighter |
| Stiff beam (bending) | 39% heavier | lighter |
| Stiff panel or plate | lighter | 50% heavier |
| Strong rod or tie | 3.02x heavier | lighter |
| Strong beam | 12% heavier | lighter |
| Strong panel or plate | lighter | 47% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic Polycarbonate or Stainless Steel 17-4PH?
Plastic Polycarbonate stretches further before it breaks: 125% elongation at break against 9% for Stainless Steel 17-4PH.
Thermal
Which handles higher temperatures, Plastic Polycarbonate or Stainless Steel 17-4PH?
Stainless Steel 17-4PH does: 316 °C against 125 °C for Plastic Polycarbonate.
Which conducts heat better, Plastic Polycarbonate or Stainless Steel 17-4PH?
Stainless Steel 17-4PH conducts heat better: 17.9 W/m·K against 0.2 W/m·K for Plastic Polycarbonate.
Which expands less with temperature?
Stainless Steel 17-4PH expands less: 10.8 µm/m·K against 65 µm/m·K for Plastic Polycarbonate.
Related comparisons
- Plastic Polycarbonate vs. Plastic Nylon
- Plastic Polycarbonate vs. SLA Resin Standard
- Plastic Polycarbonate vs. FDM Polycarbonate
- Plastic Polycarbonate vs. Plastic POM/Acetal
- Stainless Steel 17-4PH vs. Nickel Inconel 718
- Stainless Steel 17-4PH vs. Steel AISI 4340
- Stainless Steel 17-4PH vs. DMLS 17-4PH Stainless Steel
- Stainless Steel 17-4PH vs. DMLS Ti-6Al-4V ELI Titanium