Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
EOS PA 2200 (PA12) Material Data Sheet, process parameter 'Balance' at 120 µm layer thickness, X orientation, dry (conditioned values not given). Live MDS status 04.10.2026, last changed 10.09.2026; PDF via ?topdf=... link on the same page.
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium · Ultimate tensile strength: typical, plate, annealedTitanium · Elongation at break: typical, in 2 in., plate annealedTitanium · Density: nominalTitanium · Poisson's ratio: mean of TIMET measurementsTitanium · Melting point: melting rangeTitanium · Max service temperature: upper recommended use temperature
2
PA 2200 Balance Material Data SheetEOS GmbHSLS PA12 Nylon · Ultimate tensile strength: typicalSLS PA12 Nylon · Elongation at break: typicalSLS PA12 Nylon · Young's modulus (stiffness): typicalSLS PA12 Nylon · Density: typicalSLS PA12 Nylon · Melting point: typicalSLS PA12 Nylon · Max service temperature: HDT 1.8 MPa, X orientation
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium · Young's modulus (stiffness): typical range, 20 °CTitanium · Thermal conductivity: typical, 20 °C, mill annealedTitanium · Thermal expansion: typical, mean 0-100 °CTitanium · Specific heat: typical, 20 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLS PA12 Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is SLS PA12 Nylon stronger than Titanium?
Titanium is stronger: its yield strength is 885 MPa against tensile strength 48 MPa for SLS PA12 Nylon (18.4x).
Which is lighter, SLS PA12 Nylon or Titanium?
SLS PA12 Nylon is lighter: 930 kg/m³ against 4,430 kg/m³ for Titanium.
Which is stiffer, SLS PA12 Nylon or Titanium?
Titanium is stiffer: Young's modulus 115 GPa against 1.65 GPa for SLS PA12 Nylon, so the same part in Titanium deflects less under the same load.
Which is lighter for the same job, SLS PA12 Nylon or Titanium?
For the same stiffness or strength: SLS PA12 Nylon is lighter for a stiff panel or plate, strong panel or plate; Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
SLS PA12 Nylon
Titanium
Stiff rod or tie (tension)
14.6x heavier
lighter
Stiff beam (bending)
1.75x heavier
lighter
Stiff panel or plate
lighter
16% heavier
Strong rod or tie
3.87x heavier
lighter
Strong beam
47% heavier
lighter
Strong panel or plate
lighter
11% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, SLS PA12 Nylon or Titanium?
SLS PA12 Nylon stretches further before it breaks: 18% elongation at break against 16% for Titanium.