Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Cleveland-Cliffs, TIMET, Steel Construction Institute
Stainless Steel 304
Type 304, annealed flat-rolled (Cleveland-Cliffs 304/304L Product Data Bulletin, May 2021); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
304/304L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 304 · Yield strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Ultimate tensile strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Elongation at break: typical, annealed, in 2 in. (50.8 mm)Stainless Steel 304 · Young's modulus (stiffness): typical, in tensionStainless Steel 304 · Density: typicalStainless Steel 304 · Thermal conductivity: at 100 °CStainless Steel 304 · Thermal expansion: mean, 0–100 °CStainless Steel 304 · Specific heat: mean, 0–100 °CStainless Steel 304 · Melting point: melting rangeStainless Steel 304 · Max service temperature: continuous, oxidation (scaling) limit in air
2
TIMETAL 6-4 PropertiesTIMETarchived copyTitanium Ti-6Al-4V · Yield strength: typical, plate (>0.187 in), annealed, 0.2% offsetTitanium Ti-6Al-4V · Ultimate tensile strength: typical, plate, annealedTitanium Ti-6Al-4V · Elongation at break: typical, in 2 in., plate annealedTitanium Ti-6Al-4V · Density: nominalTitanium Ti-6Al-4V · Poisson's ratio: mean of TIMET measurementsTitanium Ti-6Al-4V · Melting point: melting rangeTitanium Ti-6Al-4V · Max service temperature: upper recommended use temperature
3
TIMETAL 6-4 Data SheetTIMETarchived copyTitanium Ti-6Al-4V · Young's modulus (stiffness): typical range, 20 °CTitanium Ti-6Al-4V · Thermal conductivity: typical, 20 °C, mill annealedTitanium Ti-6Al-4V · Thermal expansion: typical, mean 0-100 °CTitanium Ti-6Al-4V · Specific heat: typical, 20 °C
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 304 · Poisson's ratio: design value (structural stainless steels)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Stainless Steel 304 stronger than Titanium Ti-6Al-4V?
Titanium Ti-6Al-4V is stronger: its yield strength is 885 MPa against 241 MPa for Stainless Steel 304 (3.67x).
Which is lighter, Stainless Steel 304 or Titanium Ti-6Al-4V?
Titanium Ti-6Al-4V is lighter: 4,430 kg/m³ against 8,030 kg/m³ for Stainless Steel 304.
Which is stiffer, Stainless Steel 304 or Titanium Ti-6Al-4V?
Stainless Steel 304 is stiffer: Young's modulus 193 GPa against 115 GPa for Titanium Ti-6Al-4V, so the same part in Stainless Steel 304 deflects less under the same load.
Which is lighter for the same job, Stainless Steel 304 or Titanium Ti-6Al-4V?
For the same stiffness or strength: Titanium Ti-6Al-4V is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Stainless Steel 304
Titanium Ti-6Al-4V
Stiff rod or tie (tension)
8% heavier
lighter
Stiff beam (bending)
40% heavier
lighter
Stiff panel or plate
1.52x heavier
lighter
Strong rod or tie
6.66x heavier
lighter
Strong beam
4.31x heavier
lighter
Strong panel or plate
3.47x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Stainless Steel 304 or Titanium Ti-6Al-4V?
Stainless Steel 304 stretches further before it breaks: 55% elongation at break against 16% for Titanium Ti-6Al-4V.
Thermal
Which conducts heat better, Stainless Steel 304 or Titanium Ti-6Al-4V?
Stainless Steel 304 conducts heat better: 16.2 W/m·K against 6.6 W/m·K for Titanium Ti-6Al-4V.
Which expands less with temperature?
Titanium Ti-6Al-4V expands less: 9 µm/m·K against 16.9 µm/m·K for Stainless Steel 304.