Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources6 documents: American Institute of Steel Construction, Nathan Trotter, bauforumstahl (ArcelorMittal), Eastern Alloys, Ovako
Steel A992
ASTM A992 W-shapes; Fy/Fu specified minimums from AISC publications (AISC 360-16 Commentary; Modern Steel Construction); elastic constants AISC 360; physical constants from the bauforumstahl structural-steel EPD, which names A992 among covered product standards.
Zinc Zamak 3
Zamak 3 (ASTM B86 die cast), Nathan Trotter (zinc alloy producer) technical data sheet, typical values
1
Updating Standard Shape Material Properties Database for Design and ReliabilityAmerican Institute of Steel Constructionarchived copySteel A992 · Yield strength: typical: mean of 20,295 A992 flange mill-test coupons (1998 SSPC survey), as reported by AISCSteel A992 · Ultimate tensile strength: typical: mean of 20,295 A992 flange mill-test coupons (1998 SSPC survey)Steel A992 · Elongation at break: typical: mean of 24,847 A992 mill-test elongations, web and flange (1998 SSPC mill data), as reported by AISC
ANSI/AISC 360-16 Specification for Structural Steel Buildings, with CommentaryAmerican Institute of Steel Constructionarchived copySteel A992 · Young's modulus (stiffness): design value (AISC 360-16)Steel A992 · Poisson's ratio: design value (AISC 360-16 Commentary)
4
Environmental Product Declaration: Structural Steel Sections and Merchant Bars (2023)bauforumstahl (ArcelorMittal)archived copySteel A992 · Density: nominal (constructional data)Steel A992 · Thermal conductivity: nominal at 20 °CSteel A992 · Thermal expansion: nominal (constructional data, no temperature range stated)
5
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
6
S275JR Steel GradeOvakoSteel A992 · Specific heat: base material: EN S275JR unalloyed structural steel (the EN counterpart of A36), typical, 50/100 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Steel A992 stronger than Zinc Zamak 3?
Steel A992 is stronger: its yield strength is 385 MPa against 221 MPa for Zinc Zamak 3 (1.74x).
Which is lighter, Steel A992 or Zinc Zamak 3?
Zinc Zamak 3 is lighter: 6,600 kg/m³ against 7,850 kg/m³ for Steel A992.
Which is stiffer, Steel A992 or Zinc Zamak 3?
Steel A992 is stiffer: Young's modulus 200 GPa against 85.5 GPa for Zinc Zamak 3, so the same part in Steel A992 deflects less under the same load.
Which is lighter for the same job, Steel A992 or Zinc Zamak 3?
For the same stiffness or strength: Steel A992 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Steel A992
Zinc Zamak 3
Stiff rod or tie (tension)
lighter
1.97x heavier
Stiff beam (bending)
lighter
29% heavier
Stiff panel or plate
lighter
12% heavier
Strong rod or tie
lighter
46% heavier
Strong beam
lighter
22% heavier
Strong panel or plate
lighter
11% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Steel A992 or Zinc Zamak 3?
Steel A992 stretches further before it breaks: 24.2% elongation at break against 10% for Zinc Zamak 3.
Thermal
Which conducts heat better, Steel A992 or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 48 W/m·K for Steel A992.
Which expands less with temperature?
Steel A992 expands less: 12 µm/m·K against 27.4 µm/m·K for Zinc Zamak 3.