Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 5052-H32 · Density: nominalAluminum 5052-H32 · Poisson's ratio: typical (handbook physical constant)Aluminum 5052-H32 · Specific heat: at 100 °C (212 °F); table covers O, H32, H34, H36, H38
4
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 5052-H32 stronger than Plastic PETG?
Aluminum 5052-H32 is stronger: its yield strength is 195 MPa against 46.2 MPa for Plastic PETG (4.22x).
Which is lighter, Aluminum 5052-H32 or Plastic PETG?
Plastic PETG is lighter: 1,270 kg/m³ against 2,685 kg/m³ for Aluminum 5052-H32.
Which is stiffer, Aluminum 5052-H32 or Plastic PETG?
Aluminum 5052-H32 is stiffer: Young's modulus 70 GPa against 1.94 GPa for Plastic PETG, so the same part in Aluminum 5052-H32 deflects less under the same load.
Which is lighter for the same job, Aluminum 5052-H32 or Plastic PETG?
For the same stiffness or strength: Aluminum 5052-H32 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; Plastic PETG is lighter for a strong panel or plate.
Part that must be
Aluminum 5052-H32
Plastic PETG
Stiff rod or tie (tension)
lighter
17.1x heavier
Stiff beam (bending)
lighter
2.84x heavier
Stiff panel or plate
lighter
1.56x heavier
Strong rod or tie
lighter
2x heavier
Strong beam
lighter
24% heavier
Strong panel or plate
3% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 5052-H32 or Plastic PETG?
Aluminum 5052-H32 stretches further before it breaks: 12% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Aluminum 5052-H32 or Plastic PETG?
Aluminum 5052-H32 conducts heat better: 138 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Aluminum 5052-H32 expands less: 23.8 µm/m·K against 51 µm/m·K for Plastic PETG.