Materials / Compare
Aluminum 6061-T6 vs. DMLS 17-4PH Stainless Steel
Compare Aluminum 6061-T6 vs. DMLS 17-4PH Stainless Steel strength, stiffness, weight and thermal properties.
| Mechanical | Aluminum 6061-T6 | DMLS 17-4PH Stainless Steel |
|---|---|---|
| Yield strength | 276MPa1 | mean861MPa23.12x stronger |
| Ultimate tensile strength | 310MPa1 | mean886MPa22.86x stronger |
| Elongation at break | 17%1 | mean at break19.9%217% more ductile |
| Young's modulus (stiffness) | 68.3GPa1 | base material197GPa32.88x stiffer |
| Density | 2,700kg/m³12.89x lighter | mean part density7,790kg/m³2 |
| Strength to weight | 102kN·m/kg | 110kN·m/kg8% higher |
| Stiffness to weight | 25.3MN·m/kg | 25.3MN·m/kg |
| Poisson's ratio | 0.334 | base material0.2723 |
| Shear modulus | 25.7GPa | 77.4GPa3.02x stiffer in shear |
| Bulk modulus | 67GPa | 144GPa2.15x higher |
| Speed of sound | 5,030m/s | 5,029m/s |
| Thermal | Aluminum 6061-T6 | DMLS 17-4PH Stainless Steel |
|---|---|---|
| Thermal conductivity | 167W/m·K19.33x more heat through a fin | base material17.9W/m·K3 |
| Thermal expansion | 23.6µm/m·K1 | mean 25-100 °C10.4µm/m·K22.27x less |
| 100 mm part over a 50 °C swing | 118µm growth | 52µm growth2.27x less |
| Specific heat | 896J/kg·K11.95x higher | base material460J/kg·K3 |
| Heats up and cools (diffusivity) | 69mm²/s13.8x faster | 5mm²/s |
| Thermal shock resistance | 19,159W/m3.5x more resistant | 5,474W/m |
| Melting point | solidus-liquidus582–652°C1 | not sourced |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources4 documents: Kaiser Aluminum, EOS GmbH, Cleveland-Cliffs, U.S. Department of Defense
- Aluminum 6061-T6
- 6061-T6/T651, Kaiser Aluminum typical properties; Poisson from MIL-HDBK-5J
- DMLS 17-4PH Stainless Steel
- EOS StainlessSteel 17-4PH IndustryLine (powder 9011-0041), EOS M 290, 40 µm, default job 17-4PH_040_StainlessM291_100, as built, horizontal; ISO 6892 & ASTM E8M
- 1Alloy 6061 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum 6061-T6 · Yield strength: typical, 0.2% offset, .500 in dia specimenAluminum 6061-T6 · Ultimate tensile strength: typicalAluminum 6061-T6 · Elongation at break: typical, in 4D, 0.500 in dia specimenAluminum 6061-T6 · Young's modulus (stiffness): typicalAluminum 6061-T6 · Density: nominalAluminum 6061-T6 · Thermal conductivity: typical, 20 °CAluminum 6061-T6 · Thermal expansion: typical, mean 20-100 °CAluminum 6061-T6 · Specific heat: typical, at 100 °CAluminum 6061-T6 · Melting point: solidus-liquidus
- 2EOS StainlessSteel 17-4PH IndustryLine Material Data Sheet, M 290EOS GmbHarchived copyDMLS 17-4PH Stainless Steel · Yield strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Ultimate tensile strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Elongation at break: mean at break, as built, horizontalDMLS 17-4PH Stainless Steel · Density: mean part density (ISO 3369)DMLS 17-4PH Stainless Steel · Thermal expansion: mean 25-100 °C, ASTM E228, AFTER atmospheric heat treatment (as-built value not published)
- 317-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsDMLS 17-4PH Stainless Steel · Young's modulus (stiffness): base material: wrought 17-4 PH, Condition H 900 (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Poisson's ratio: base material: wrought 17-4 PH, all conditions (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Thermal conductivity: base material: wrought 17-4 PH, Condition H 900, at 149 °C (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Specific heat: base material: wrought 17-4 PH, Condition A, 0-100 °C (Cleveland-Cliffs)
- 4MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 6061-T6 · Poisson's ratio: typical (handbook physical constant)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 17-4PH Stainless Steel is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 6061-T6 stronger than DMLS 17-4PH Stainless Steel?
DMLS 17-4PH Stainless Steel is stronger: its yield strength is 861 MPa against 276 MPa for Aluminum 6061-T6 (3.12x).
Which is lighter, Aluminum 6061-T6 or DMLS 17-4PH Stainless Steel?
Aluminum 6061-T6 is lighter: 2,700 kg/m³ against 7,790 kg/m³ for DMLS 17-4PH Stainless Steel.
Which is stiffer, Aluminum 6061-T6 or DMLS 17-4PH Stainless Steel?
DMLS 17-4PH Stainless Steel is stiffer: Young's modulus 197 GPa against 68.3 GPa for Aluminum 6061-T6, so the same part in DMLS 17-4PH Stainless Steel deflects less under the same load.
Which is lighter for the same job, Aluminum 6061-T6 or DMLS 17-4PH Stainless Steel?
For the same stiffness or strength: Aluminum 6061-T6 is lighter for a stiff beam (bending), stiff panel or plate, strong beam, strong panel or plate; DMLS 17-4PH Stainless Steel is lighter for a strong rod or tie.
| Part that must be | Aluminum 6061-T6 | DMLS 17-4PH Stainless Steel |
|---|---|---|
| Stiff rod or tie (tension) | about equal | about equal |
| Stiff beam (bending) | lighter | 1.7x heavier |
| Stiff panel or plate | lighter | 2.03x heavier |
| Strong rod or tie | 8% heavier | lighter |
| Strong beam | lighter | 35% heavier |
| Strong panel or plate | lighter | 1.63x heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 6061-T6 or DMLS 17-4PH Stainless Steel?
DMLS 17-4PH Stainless Steel stretches further before it breaks: 19.9% elongation at break against 17% for Aluminum 6061-T6.
Thermal
Which conducts heat better, Aluminum 6061-T6 or DMLS 17-4PH Stainless Steel?
Aluminum 6061-T6 conducts heat better: 167 W/m·K against 17.9 W/m·K for DMLS 17-4PH Stainless Steel.
Which expands less with temperature?
DMLS 17-4PH Stainless Steel expands less: 10.4 µm/m·K against 23.6 µm/m·K for Aluminum 6061-T6.
Related comparisons
- Aluminum 6061-T6 vs. Aluminum
- Aluminum 6061-T6 vs. DMLS AlSi10Mg Aluminum
- Aluminum 6061-T6 vs. Aluminum 2024-T351
- Aluminum 6061-T6 vs. Aluminum 6063-T6
- DMLS 17-4PH Stainless Steel vs. Steel AISI 4340
- DMLS 17-4PH Stainless Steel vs. Nickel Inconel 718
- DMLS 17-4PH Stainless Steel vs. Stainless Steel 17-4PH
- DMLS 17-4PH Stainless Steel vs. Steel AISI 1045