Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Kaiser Aluminum, Cleveland-Cliffs, U.S. Department of Defense, National Institute of Standards and Technology
Aluminum 7050-T7451
7050-T7451 plate, Kaiser Aluminum sheet, coil & plate typical datasheet (longitudinal); Poisson from MIL-HDBK-5J
Iron
Cleveland-Cliffs / AK Steel ARMCO Pure Iron Product Data Bulletin (07/2022): Table 1 typical physical properties, Table 2 typical mechanical properties after SRA/recrystallization anneal.
ARMCO Pure Iron Product Data Bulletin (2022)Cleveland-Cliffsarchived copyIron · Yield strength: typical (0.2% YS), hot rolled + SRA/recrystallization annealIron · Ultimate tensile strength: typical, SRA/recrystallization annealIron · Elongation at break: typical, gauge 4D0Iron · Young's modulus (stiffness): typical, after SRA/recrystallization annealIron · Density: typicalIron · Thermal conductivity: typical at 20 °CIron · Thermal expansion: mean, 20-399 °CIron · Specific heat: typicalIron · Melting point: typical
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7050-T7451 · Poisson's ratio: typical (handbook physical constant)
4
Elastic Properties of Metals and Alloys, I. Iron, Nickel, and Iron-Nickel Alloys, J. Phys. Chem. Ref. Data 2 (1973)National Institute of Standards and Technologyarchived copyIron · Poisson's ratio: NIST critically evaluated best value (polycrystalline iron)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7050-T7451 stronger than Iron?
Aluminum 7050-T7451 is stronger: its yield strength is 469 MPa against 186 MPa for Iron (2.52x).
Which is lighter, Aluminum 7050-T7451 or Iron?
Aluminum 7050-T7451 is lighter: 2,830 kg/m³ against 7,860 kg/m³ for Iron.
Which is stiffer, Aluminum 7050-T7451 or Iron?
Iron is stiffer: Young's modulus 207 GPa against 70.3 GPa for Aluminum 7050-T7451, so the same part in Iron deflects less under the same load.
Which is lighter for the same job, Aluminum 7050-T7451 or Iron?
For the same stiffness or strength: Aluminum 7050-T7451 is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Iron is lighter for a stiff rod or tie (tension).
Part that must be
Aluminum 7050-T7451
Iron
Stiff rod or tie (tension)
6% heavier
lighter
Stiff beam (bending)
lighter
1.62x heavier
Stiff panel or plate
lighter
1.94x heavier
Strong rod or tie
lighter
7x heavier
Strong beam
lighter
5.15x heavier
Strong panel or plate
lighter
4.41x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7050-T7451 or Iron?
Iron stretches further before it breaks: 38% elongation at break against 11% for Aluminum 7050-T7451.
Thermal
Which conducts heat better, Aluminum 7050-T7451 or Iron?
Aluminum 7050-T7451 conducts heat better: 157 W/m·K against 73.2 W/m·K for Iron.
Which expands less with temperature?
Iron expands less: 13.7 µm/m·K against 23.5 µm/m·K for Aluminum 7050-T7451.