Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Kaiser Aluminum, Outokumpu, U.S. Department of Defense, Steel Construction Institute, Carpenter Technology
Aluminum 7050-T7451
7050-T7451 plate, Kaiser Aluminum sheet, coil & plate typical datasheet (longitudinal); Poisson from MIL-HDBK-5J
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7050-T7451 · Poisson's ratio: typical (handbook physical constant)
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
5
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7050-T7451 stronger than Stainless Steel 303?
Aluminum 7050-T7451 is stronger: its yield strength is 469 MPa against 275 MPa for Stainless Steel 303 (1.71x).
Which is lighter, Aluminum 7050-T7451 or Stainless Steel 303?
Aluminum 7050-T7451 is lighter: 2,830 kg/m³ against 7,900 kg/m³ for Stainless Steel 303.
Which is stiffer, Aluminum 7050-T7451 or Stainless Steel 303?
Stainless Steel 303 is stiffer: Young's modulus 200 GPa against 70.3 GPa for Aluminum 7050-T7451, so the same part in Stainless Steel 303 deflects less under the same load.
Which is lighter for the same job, Aluminum 7050-T7451 or Stainless Steel 303?
For the same stiffness or strength: Aluminum 7050-T7451 is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension).
Part that must be
Aluminum 7050-T7451
Stainless Steel 303
Stiff rod or tie (tension)
2% heavier
lighter
Stiff beam (bending)
lighter
1.66x heavier
Stiff panel or plate
lighter
1.97x heavier
Strong rod or tie
lighter
4.76x heavier
Strong beam
lighter
3.98x heavier
Strong panel or plate
lighter
3.65x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7050-T7451 or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 11% for Aluminum 7050-T7451.
Thermal
Which conducts heat better, Aluminum 7050-T7451 or Stainless Steel 303?
Aluminum 7050-T7451 conducts heat better: 157 W/m·K against 15 W/m·K for Stainless Steel 303.
Which expands less with temperature?
Stainless Steel 303 expands less: 16 µm/m·K against 23.5 µm/m·K for Aluminum 7050-T7451.