Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Alloy 7075 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum 7075-T6 · Density: nominalAluminum 7075-T6 · Thermal conductivity: typical, 20 °C, T651Aluminum 7075-T6 · Thermal expansion: typical, mean 20-100 °CAluminum 7075-T6 · Specific heat: typical, at 100 °CAluminum 7075-T6 · Melting point: melting range
4
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7075-T6 · Poisson's ratio: typical (handbook physical constant)
5
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 7075-T6 stronger than Plastic PETG?
Aluminum 7075-T6 is stronger: its yield strength is 503 MPa against 46.2 MPa for Plastic PETG (10.9x).
Which is lighter, Aluminum 7075-T6 or Plastic PETG?
Plastic PETG is lighter: 1,270 kg/m³ against 2,800 kg/m³ for Aluminum 7075-T6.
Which is stiffer, Aluminum 7075-T6 or Plastic PETG?
Aluminum 7075-T6 is stiffer: Young's modulus 71 GPa against 1.94 GPa for Plastic PETG, so the same part in Aluminum 7075-T6 deflects less under the same load.
Which is lighter for the same job, Aluminum 7075-T6 or Plastic PETG?
For the same stiffness or strength: Aluminum 7075-T6 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 7075-T6
Plastic PETG
Stiff rod or tie (tension)
lighter
16.6x heavier
Stiff beam (bending)
lighter
2.74x heavier
Stiff panel or plate
lighter
1.51x heavier
Strong rod or tie
lighter
4.94x heavier
Strong beam
lighter
2.23x heavier
Strong panel or plate
lighter
50% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7075-T6 or Plastic PETG?
Aluminum 7075-T6 stretches further before it breaks: 11% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Aluminum 7075-T6 or Plastic PETG?
Aluminum 7075-T6 conducts heat better: 130 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Aluminum 7075-T6 expands less: 23.4 µm/m·K against 51 µm/m·K for Plastic PETG.