Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Kaiser Aluminum, Victrex, U.S. Department of Defense
Aluminum
6061-T6/T651, Kaiser Aluminum typical properties (sheet, coil & plate datasheet); Poisson from MIL-HDBK-5J
Plastic PEEK
Victrex PEEK 450G (unreinforced, injection moulded), Victrex TDS rev. March 2026; Poisson from Victrex fluid-management flyer (2020-07)
1
Alloy 6061 Sheet, Coil & Plate Technical DataKaiser Aluminumarchived copyAluminum · Yield strength: typical, 0.2% offset, .500 in dia specimenAluminum · Ultimate tensile strength: typicalAluminum · Elongation at break: typical, in 4D, 0.500 in dia specimenAluminum · Young's modulus (stiffness): typicalAluminum · Density: nominalAluminum · Thermal conductivity: typical, 20 °CAluminum · Thermal expansion: typical, mean 20-100 °CAluminum · Specific heat: typical, at 100 °CAluminum · Melting point: solidus-liquidus
2
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum · Poisson's ratio: typical (handbook physical constant)
4
VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
5
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum stronger than Plastic PEEK?
Aluminum is stronger: its yield strength is 276 MPa against 98 MPa for Plastic PEEK (2.82x).
Which is lighter, Aluminum or Plastic PEEK?
Plastic PEEK is lighter: 1,300 kg/m³ against 2,700 kg/m³ for Aluminum.
Which is stiffer, Aluminum or Plastic PEEK?
Aluminum is stiffer: Young's modulus 68.3 GPa against 4 GPa for Plastic PEEK, so the same part in Aluminum deflects less under the same load.
Which is lighter for the same job, Aluminum or Plastic PEEK?
For the same stiffness or strength: Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie; Plastic PEEK is lighter for a strong beam, strong panel or plate.
Part that must be
Aluminum
Plastic PEEK
Stiff rod or tie (tension)
lighter
8.22x heavier
Stiff beam (bending)
lighter
1.99x heavier
Stiff panel or plate
lighter
24% heavier
Strong rod or tie
lighter
36% heavier
Strong beam
4% heavier
lighter
Strong panel or plate
24% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum or Plastic PEEK?
Plastic PEEK stretches further before it breaks: 25% elongation at break against 17% for Aluminum.
Thermal
Which conducts heat better, Aluminum or Plastic PEEK?
Aluminum conducts heat better: 167 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
Aluminum expands less: 23.6 µm/m·K against 55 µm/m·K for Plastic PEEK.