Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Hostalen 23050 B Product DataLyondellBasellPlastic HDPE · Yield strength: typical, tensile stress at yield 23 °C, 50 mm/min ISO 527Plastic HDPE · Young's modulus (stiffness): typical, tensile modulus 23 °C ISO 527Plastic HDPE · Density: typical, ISO 1183
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
4
Typical Engineering Properties of High Density PolyethyleneINEOS Olefins & Polymers USAarchived copyPlastic HDPE · Poisson's ratio: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Thermal conductivity: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Thermal expansion: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)Plastic HDPE · Specific heat: base material: high-density polyethylene family (INEOS Olefins & Polymers USA, Typical Engineering Properties of HDPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Plastic HDPE?
Brass C360 is stronger: its yield strength is 310 MPa against 24 MPa for Plastic HDPE (12.9x).
Which is lighter, Brass C360 or Plastic HDPE?
Plastic HDPE is lighter: 950 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Plastic HDPE?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 0.9 GPa for Plastic HDPE, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or Plastic HDPE?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie; Plastic HDPE is lighter for a stiff panel or plate, strong beam, strong panel or plate.
Part that must be
Brass C360
Plastic HDPE
Stiff rod or tie (tension)
lighter
12x heavier
Stiff beam (bending)
lighter
16% heavier
Stiff panel or plate
1.88x heavier
lighter
Strong rod or tie
lighter
44% heavier
Strong beam
1.62x heavier
lighter
Strong panel or plate
2.49x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Brass C360 or Plastic HDPE?
Brass C360 conducts heat better: 116 W/m·K against 0.445 W/m·K for Plastic HDPE.
Which expands less with temperature?
Brass C360 expands less: 20.5 µm/m·K against 120 µm/m·K for Plastic HDPE.