Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Copper Development Association, Celanese, Wieland
Brass C360
C36000 free-cutting brass, H02 half-hard rod 1 in. section (20% cold work), copper.org typical values
Plastic UHMWPE
Celanese GUR 4120 (avg. molecular weight 4.7x10^6 g/mol), typical values on compression-molded specimens; CTE and thermal conductivity from Celanese's generic UHMWPE guide (grade not named)
GUR UHMW-PE Overview (GUR-015)CelanesePlastic UHMWPE · Yield strength: typical, tensile stress at yield ISO 527, 50 mm/minPlastic UHMWPE · Ultimate tensile strength: typical, tensile stress at break ISO 527, 50 mm/minPlastic UHMWPE · Elongation at break: typical, nominal elongation at break ISO 527Plastic UHMWPE · Young's modulus (stiffness): typical, tensile modulus ISO 527, 1 mm/minPlastic UHMWPE · Density: typicalPlastic UHMWPE · Melting point: DSC 10 K/minPlastic UHMWPE · Max service temperature: recommended max constant operating temperature
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
4
GUR UHMW-PE Polymer Guide (GUR-003)Celanesearchived copyPlastic UHMWPE · Thermal conductivity: typical, unfilled (narrative value, generic Celanese UHMWPE)Plastic UHMWPE · Thermal expansion: typical, 20 to 100 °C (generic Celanese UHMWPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Plastic UHMWPE?
Brass C360 is stronger: its yield strength is 310 MPa against 20 MPa for Plastic UHMWPE (15.5x).
Which is lighter, Brass C360 or Plastic UHMWPE?
Plastic UHMWPE is lighter: 930 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Plastic UHMWPE?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 0.66 GPa for Plastic UHMWPE, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or Plastic UHMWPE?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie; Plastic UHMWPE is lighter for a stiff panel or plate, strong beam, strong panel or plate.
Part that must be
Brass C360
Plastic UHMWPE
Stiff rod or tie (tension)
lighter
16x heavier
Stiff beam (bending)
lighter
32% heavier
Stiff panel or plate
1.73x heavier
lighter
Strong rod or tie
lighter
1.7x heavier
Strong beam
47% heavier
lighter
Strong panel or plate
2.32x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or Plastic UHMWPE?
Plastic UHMWPE stretches further before it breaks: 465% elongation at break against 25% for Brass C360.
Thermal
Which conducts heat better, Brass C360 or Plastic UHMWPE?
Brass C360 conducts heat better: 116 W/m·K against 0.4 W/m·K for Plastic UHMWPE.
Which expands less with temperature?
Brass C360 expands less: 20.5 µm/m·K against 200 µm/m·K for Plastic UHMWPE.