Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
17-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 17-4PH · Yield strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Ultimate tensile strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Elongation at break: typical, transverse, in 2 in. (50.8 mm)Stainless Steel 17-4PH · Young's modulus (stiffness): H 900Stainless Steel 17-4PH · Density: H 900Stainless Steel 17-4PH · Poisson's ratio: H 900 (column)Stainless Steel 17-4PH · Thermal conductivity: at 149 °C (300 °F), H 900Stainless Steel 17-4PH · Thermal expansion: mean, 21–93 °C (70–200 °F), H 900Stainless Steel 17-4PH · Specific heat: mean, 0–100 °C, H 900Stainless Steel 17-4PH · Max service temperature: strength-retention limit (not oxidation)
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stronger: its yield strength is 1,275 MPa against 310 MPa for Brass C360 (4.11x).
Which is lighter, Brass C360 or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is lighter: 7,800 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stiffer: Young's modulus 197 GPa against 96.5 GPa for Brass C360, so the same part in Stainless Steel 17-4PH deflects less under the same load.
Which is lighter for the same job, Brass C360 or Stainless Steel 17-4PH?
For the same stiffness or strength: Stainless Steel 17-4PH is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
Stainless Steel 17-4PH
Stiff rod or tie (tension)
2.22x heavier
lighter
Stiff beam (bending)
1.56x heavier
lighter
Stiff panel or plate
38% heavier
lighter
Strong rod or tie
4.48x heavier
lighter
Strong beam
2.8x heavier
lighter
Strong panel or plate
2.21x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or Stainless Steel 17-4PH?
Brass C360 stretches further before it breaks: 25% elongation at break against 9% for Stainless Steel 17-4PH.
Thermal
Which conducts heat better, Brass C360 or Stainless Steel 17-4PH?
Brass C360 conducts heat better: 116 W/m·K against 17.9 W/m·K for Stainless Steel 17-4PH.
Which expands less with temperature?
Stainless Steel 17-4PH expands less: 10.8 µm/m·K against 20.5 µm/m·K for Brass C360.