Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
3
Wieland-K32 (Cu-ETP, C11000) Data SheetWielandarchived copyCopper C110 · Poisson's ratio: reference value at room temperature (Wieland-K32 = Cu-ETP = C11000, rolled products)
4
VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
5
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Copper C110 stronger than Plastic PEEK?
Plastic PEEK is stronger: its yield strength is 98 MPa against 69 MPa for Copper C110 (42%).
Which is lighter, Copper C110 or Plastic PEEK?
Plastic PEEK is lighter: 1,300 kg/m³ against 8,913 kg/m³ for Copper C110.
Which is stiffer, Copper C110 or Plastic PEEK?
Copper C110 is stiffer: Young's modulus 117 GPa against 4 GPa for Plastic PEEK, so the same part in Copper C110 deflects less under the same load.
Which is lighter for the same job, Copper C110 or Plastic PEEK?
For the same stiffness or strength: Copper C110 is lighter for a stiff rod or tie (tension); Plastic PEEK is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Copper C110
Plastic PEEK
Stiff rod or tie (tension)
lighter
4.27x heavier
Stiff beam (bending)
27% heavier
lighter
Stiff panel or plate
2.22x heavier
lighter
Strong rod or tie
9.74x heavier
lighter
Strong beam
8.66x heavier
lighter
Strong panel or plate
8.17x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Copper C110 or Plastic PEEK?
Copper C110 stretches further before it breaks: 55% elongation at break against 25% for Plastic PEEK.
Thermal
Which conducts heat better, Copper C110 or Plastic PEEK?
Copper C110 conducts heat better: 391 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
Copper C110 expands less: 16.9 µm/m·K against 55 µm/m·K for Plastic PEEK.