Materials / Compare
DMLS 17-4PH Stainless Steel vs. SLA Resin Standard
Compare DMLS 17-4PH Stainless Steel vs. SLA Resin Standard strength, stiffness, weight and thermal properties.
| Mechanical | DMLS 17-4PH Stainless Steel | SLA Resin Standard |
|---|---|---|
| Yield strength | mean861MPa1 | not given (tensile used) |
| Ultimate tensile strength | mean886MPa114.8x stronger | 60MPa2 |
| Flexural strength | not sourced | 105MPa2 |
| Elongation at break | mean at break19.9%12.49x more ductile | 8%2 |
| Young's modulus (stiffness) | base material197GPa371.6x stiffer | 2.75GPa2 |
| Density | mean part density7,790kg/m³1 | 1,210kg/m³46.44x lighter |
| Strength to weight | 110kN·m/kg2.23x higher | 49.6kN·m/kg |
| Stiffness to weight | 25.3MN·m/kg11.1x higher | 2.27MN·m/kg |
| Poisson's ratio | base material0.2723 | not sourced |
| Shear modulus | 77.4GPa | not sourced |
| Bulk modulus | 144GPa | not sourced |
| Speed of sound | 5,029m/s3.34x faster | 1,508m/s |
| Thermal | DMLS 17-4PH Stainless Steel | SLA Resin Standard |
|---|---|---|
| Thermal conductivity | base material17.9W/m·K333.1x more heat through a fin | 0.54W/m·K5 |
| Thermal expansion | mean 25-100 °C10.4µm/m·K111x less | mean -30 to 140 °C114µm/m·K5 |
| 100 mm part over a 50 °C swing | 52µm growth11x less | 571µm growth |
| Specific heat | base material460J/kg·K3 | 1,800J/kg·K53.91x higher |
| Heats up and cools (diffusivity) | 5mm²/s20.1x faster | 0.248mm²/s |
| Thermal shock resistance | 5,474W/m | not sourced |
| Max service temperature | not sourced | HDT 1.8 MPa59°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources5 documents: EOS GmbH, Formlabs, Cleveland-Cliffs
- DMLS 17-4PH Stainless Steel
- EOS StainlessSteel 17-4PH IndustryLine (powder 9011-0041), EOS M 290, 40 µm, default job 17-4PH_040_StainlessM291_100, as built, horizontal; ISO 6892 & ASTM E8M
- SLA Resin Standard
- Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
- 1EOS StainlessSteel 17-4PH IndustryLine Material Data Sheet, M 290EOS GmbHarchived copyDMLS 17-4PH Stainless Steel · Yield strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Ultimate tensile strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Elongation at break: mean at break, as built, horizontalDMLS 17-4PH Stainless Steel · Density: mean part density (ISO 3369)DMLS 17-4PH Stainless Steel · Thermal expansion: mean 25-100 °C, ASTM E228, AFTER atmospheric heat treatment (as-built value not published)
- 2Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
- 317-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsDMLS 17-4PH Stainless Steel · Young's modulus (stiffness): base material: wrought 17-4 PH, Condition H 900 (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Poisson's ratio: base material: wrought 17-4 PH, all conditions (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Thermal conductivity: base material: wrought 17-4 PH, Condition H 900, at 149 °C (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Specific heat: base material: wrought 17-4 PH, Condition A, 0-100 °C (Cleveland-Cliffs)
- 4Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
- 5Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 17-4PH Stainless Steel and SLA Resin Standard are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS 17-4PH Stainless Steel stronger than SLA Resin Standard?
DMLS 17-4PH Stainless Steel is stronger: its yield strength is 861 MPa against tensile strength 60 MPa for SLA Resin Standard (14.3x).
Which is lighter, DMLS 17-4PH Stainless Steel or SLA Resin Standard?
SLA Resin Standard is lighter: 1,210 kg/m³ against 7,790 kg/m³ for DMLS 17-4PH Stainless Steel.
Which is stiffer, DMLS 17-4PH Stainless Steel or SLA Resin Standard?
DMLS 17-4PH Stainless Steel is stiffer: Young's modulus 197 GPa against 2.75 GPa for SLA Resin Standard, so the same part in DMLS 17-4PH Stainless Steel deflects less under the same load.
Which is lighter for the same job, DMLS 17-4PH Stainless Steel or SLA Resin Standard?
For the same stiffness or strength: DMLS 17-4PH Stainless Steel is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie; SLA Resin Standard is lighter for a stiff panel or plate, strong beam, strong panel or plate.
| Part that must be | DMLS 17-4PH Stainless Steel | SLA Resin Standard |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 11.1x heavier |
| Stiff beam (bending) | lighter | 31% heavier |
| Stiff panel or plate | 1.55x heavier | lighter |
| Strong rod or tie | lighter | 2.23x heavier |
| Strong beam | 9% heavier | lighter |
| Strong panel or plate | 1.7x heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS 17-4PH Stainless Steel or SLA Resin Standard?
DMLS 17-4PH Stainless Steel stretches further before it breaks: 19.9% elongation at break against 8% for SLA Resin Standard.
Thermal
Which conducts heat better, DMLS 17-4PH Stainless Steel or SLA Resin Standard?
DMLS 17-4PH Stainless Steel conducts heat better: 17.9 W/m·K against 0.54 W/m·K for SLA Resin Standard.
Which expands less with temperature?
DMLS 17-4PH Stainless Steel expands less: 10.4 µm/m·K against 114 µm/m·K for SLA Resin Standard.
Related comparisons
- DMLS 17-4PH Stainless Steel vs. Steel AISI 4340
- DMLS 17-4PH Stainless Steel vs. Nickel Inconel 718
- DMLS 17-4PH Stainless Steel vs. Stainless Steel 17-4PH
- DMLS 17-4PH Stainless Steel vs. Steel AISI 1045
- SLA Resin Standard vs. Plastic Polycarbonate
- SLA Resin Standard vs. Plastic Nylon
- SLA Resin Standard vs. FDM Polycarbonate
- SLA Resin Standard vs. Plastic POM/Acetal