Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: EOS GmbH, Nathan Trotter, Cleveland-Cliffs, Eastern Alloys
DMLS 17-4PH Stainless Steel
EOS StainlessSteel 17-4PH IndustryLine (powder 9011-0041), EOS M 290, 40 µm, default job 17-4PH_040_StainlessM291_100, as built, horizontal; ISO 6892 & ASTM E8M
Zinc Zamak 3
Zamak 3 (ASTM B86 die cast), Nathan Trotter (zinc alloy producer) technical data sheet, typical values
1
EOS StainlessSteel 17-4PH IndustryLine Material Data Sheet, M 290EOS GmbHarchived copyDMLS 17-4PH Stainless Steel · Yield strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Ultimate tensile strength: mean, as built, horizontal (N=72)DMLS 17-4PH Stainless Steel · Elongation at break: mean at break, as built, horizontalDMLS 17-4PH Stainless Steel · Density: mean part density (ISO 3369)DMLS 17-4PH Stainless Steel · Thermal expansion: mean 25-100 °C, ASTM E228, AFTER atmospheric heat treatment (as-built value not published)
17-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsDMLS 17-4PH Stainless Steel · Young's modulus (stiffness): base material: wrought 17-4 PH, Condition H 900 (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Poisson's ratio: base material: wrought 17-4 PH, all conditions (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Thermal conductivity: base material: wrought 17-4 PH, Condition H 900, at 149 °C (Cleveland-Cliffs)DMLS 17-4PH Stainless Steel · Specific heat: base material: wrought 17-4 PH, Condition A, 0-100 °C (Cleveland-Cliffs)
4
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 17-4PH Stainless Steel is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS 17-4PH Stainless Steel stronger than Zinc Zamak 3?
DMLS 17-4PH Stainless Steel is stronger: its yield strength is 861 MPa against 221 MPa for Zinc Zamak 3 (3.89x).
Which is lighter, DMLS 17-4PH Stainless Steel or Zinc Zamak 3?
Zinc Zamak 3 is lighter: 6,600 kg/m³ against 7,790 kg/m³ for DMLS 17-4PH Stainless Steel.
Which is stiffer, DMLS 17-4PH Stainless Steel or Zinc Zamak 3?
DMLS 17-4PH Stainless Steel is stiffer: Young's modulus 197 GPa against 85.5 GPa for Zinc Zamak 3, so the same part in DMLS 17-4PH Stainless Steel deflects less under the same load.
Which is lighter for the same job, DMLS 17-4PH Stainless Steel or Zinc Zamak 3?
For the same stiffness or strength: DMLS 17-4PH Stainless Steel is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
DMLS 17-4PH Stainless Steel
Zinc Zamak 3
Stiff rod or tie (tension)
lighter
1.95x heavier
Stiff beam (bending)
lighter
29% heavier
Stiff panel or plate
lighter
12% heavier
Strong rod or tie
lighter
3.3x heavier
Strong beam
lighter
2.1x heavier
Strong panel or plate
lighter
1.67x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS 17-4PH Stainless Steel or Zinc Zamak 3?
DMLS 17-4PH Stainless Steel stretches further before it breaks: 19.9% elongation at break against 10% for Zinc Zamak 3.
Thermal
Which conducts heat better, DMLS 17-4PH Stainless Steel or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 17.9 W/m·K for DMLS 17-4PH Stainless Steel.
Which expands less with temperature?
DMLS 17-4PH Stainless Steel expands less: 10.4 µm/m·K against 27.4 µm/m·K for Zinc Zamak 3.