Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
EOS StainlessSteel 316L Material Data Sheet, M 280 and M 290 (2014)EOS GmbHarchived copyDMLS 316L Stainless Steel · Young's modulus (stiffness): typical, as built, horizontal (XY); EOSINT M280-400W / M290-400W, 316L_Surface 1.0, 20 µm (2014 sheet)
4
EOS StainlessSteel 316L Material Data Sheet, FlexLine, M 290 (2016)EOS GmbHarchived copyDMLS 316L Stainless Steel · Density: part density (ISO 3369, not labelled min or typical), EOS M 290, 40 µm FlexLine
5
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyDMLS 316L Stainless Steel · Poisson's ratio: base material: austenitic stainless steels incl. 1.4404 (316L), design value
6
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
7
316/316L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsDMLS 316L Stainless Steel · Thermal conductivity: base material: wrought 316/316L (Cleveland-Cliffs), at 100 °CDMLS 316L Stainless Steel · Specific heat: base material: wrought 316/316L (Cleveland-Cliffs), 0-100 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 316L Stainless Steel is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS 316L Stainless Steel stronger than Zinc Zamak 3?
DMLS 316L Stainless Steel is stronger: its yield strength is 530 MPa against 221 MPa for Zinc Zamak 3 (2.4x).
Which is lighter, DMLS 316L Stainless Steel or Zinc Zamak 3?
Zinc Zamak 3 is lighter: 6,600 kg/m³ against 7,900 kg/m³ for DMLS 316L Stainless Steel.
Which is stiffer, DMLS 316L Stainless Steel or Zinc Zamak 3?
DMLS 316L Stainless Steel is stiffer: Young's modulus 185 GPa against 85.5 GPa for Zinc Zamak 3, so the same part in DMLS 316L Stainless Steel deflects less under the same load.
Which is lighter for the same job, DMLS 316L Stainless Steel or Zinc Zamak 3?
For the same stiffness or strength: DMLS 316L Stainless Steel is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
DMLS 316L Stainless Steel
Zinc Zamak 3
Stiff rod or tie (tension)
lighter
1.81x heavier
Stiff beam (bending)
lighter
23% heavier
Stiff panel or plate
lighter
8% heavier
Strong rod or tie
lighter
2x heavier
Strong beam
lighter
50% heavier
Strong panel or plate
lighter
29% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS 316L Stainless Steel or Zinc Zamak 3?
DMLS 316L Stainless Steel stretches further before it breaks: 40% elongation at break against 10% for Zinc Zamak 3.
Thermal
Which conducts heat better, DMLS 316L Stainless Steel or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 16.2 W/m·K for DMLS 316L Stainless Steel.
Which expands less with temperature?
DMLS 316L Stainless Steel expands less: 15.7 µm/m·K against 27.4 µm/m·K for Zinc Zamak 3.