Materials / Compare
DMLS AlSi10Mg Aluminum vs. Plastic ABS (bulk/injection)
Compare DMLS AlSi10Mg Aluminum vs. Plastic ABS (bulk/injection) strength, stiffness, weight and thermal properties.
| Mechanical | DMLS AlSi10Mg Aluminum | Plastic ABS (bulk/injection) |
|---|---|---|
| Yield strength | 270MPa16x stronger | 45MPa2 |
| Ultimate tensile strength | 450MPa1 | not stated (yield given) |
| Flexural strength | not sourced | 65MPa2 |
| Elongation at break | 10.2%1 | 10%2 |
| Young's modulus (stiffness) | 72GPa331.3x stiffer | 2.3GPa2 |
| Density | 2,670kg/m³4 | 1,040kg/m³22.57x lighter |
| Strength to weight | 101kN·m/kg2.34x higher | 43.3kN·m/kg |
| Stiffness to weight | 27MN·m/kg12.2x higher | 2.21MN·m/kg |
| Poisson's ratio | base material0.335 | 0.396 |
| Shear modulus | 27.1GPa32.7x stiffer in shear | 0.827GPa |
| Bulk modulus | 70.6GPa20.3x higher | 3.48GPa |
| Speed of sound | 5,193m/s3.49x faster | 1,487m/s |
| Thermal | DMLS AlSi10Mg Aluminum | Plastic ABS (bulk/injection) |
|---|---|---|
| Thermal conductivity | 110W/m·K1647x more heat through a fin | 0.17W/m·K2 |
| Thermal expansion | mean 25-100 °C20µm/m·K1 | range80–110µm/m·K2 |
| 100 mm part over a 50 °C swing | 100µm growth4.75x less | 475µm growth |
| Specific heat | base material963J/kg·K5 | not sourced |
| Heats up and cools (diffusivity) | 42.8mm²/s | not sourced |
| Thermal shock resistance | 13,819W/m647x more resistant | 21.4W/m |
| Max service temperature | not sourced | HDT 1.8 MPa94°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources6 documents: EOS GmbH, INEOS Styrolution, Renishaw, U.S. Department of Defense, Covestro
- DMLS AlSi10Mg Aluminum
- EOS Aluminium AlSi10Mg (powder 9011-0024), EOS M 290 | 30 µm process (AlSi10Mg_FlexM291 2.01), as manufactured, horizontal; machined (turned) specimens, ISO 6892-1 B10
- Plastic ABS (bulk/injection)
- INEOS Styrolution Terluran GP-22 general-purpose injection-molding ABS, ISO typical values (TDS revision 08/01/2022)
- 1EOS Aluminium AlSi10Mg Material Data SheetEOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Yield strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Ultimate tensile strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Elongation at break: typical at break, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Thermal conductivity: typical, as manufactured, horizontal (ISO 22007-2)DMLS AlSi10Mg Aluminum · Thermal expansion: mean 25-100 °C, ASTM E228
- 2Terluran GP-22 (ABS) Product Data SheetINEOS StyrolutionPlastic ABS (bulk/injection) · Yield strength: typical, tensile stress at yield 23 °CPlastic ABS (bulk/injection) · Flexural strength: typical, 23 °CPlastic ABS (bulk/injection) · Elongation at break: nominal strain at break, 23 °CPlastic ABS (bulk/injection) · Young's modulus (stiffness): typicalPlastic ABS (bulk/injection) · Density: typicalPlastic ABS (bulk/injection) · Thermal conductivity: typicalPlastic ABS (bulk/injection) · Thermal expansion: rangePlastic ABS (bulk/injection) · Max service temperature: HDT 1.8 MPa (annealed 4 h/80 °C)
- 3RenAM 500 Series Aluminium AlSi10Mg Material Data SheetRenishawDMLS AlSi10Mg Aluminum · Young's modulus (stiffness): same material and process, different machine maker: Renishaw RenAM 500, 30 µm, as built, horizontal (XY)
- 4EOS Aluminium AlSi10Mg Material Data Sheet, FlexLine, M 290 (2018)EOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Density: typical part density (ISO 3369), EOS M 290, AlSi10Mg_030_FlexM291 (30 µm)
- 5MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseDMLS AlSi10Mg Aluminum · Poisson's ratio: base material: cast Al-Si-Mg alloy 359.0 (Al-9Si-0.6Mg, closest MIL-HDBK-5J alloy to AlSi10Mg / EN AC-43000)DMLS AlSi10Mg Aluminum · Specific heat: base material: cast Al-Si-Mg alloy 359.0 (MIL-HDBK-5J), at 100 °C
- 6Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic ABS (bulk/injection) · Poisson's ratio: typical, ABS family (Covestro Part and Mold Design guide, Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS AlSi10Mg Aluminum is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS AlSi10Mg Aluminum stronger than Plastic ABS (bulk/injection)?
DMLS AlSi10Mg Aluminum is stronger: its yield strength is 270 MPa against 45 MPa for Plastic ABS (bulk/injection) (6x).
Which is lighter, DMLS AlSi10Mg Aluminum or Plastic ABS (bulk/injection)?
Plastic ABS (bulk/injection) is lighter: 1,040 kg/m³ against 2,670 kg/m³ for DMLS AlSi10Mg Aluminum.
Which is stiffer, DMLS AlSi10Mg Aluminum or Plastic ABS (bulk/injection)?
DMLS AlSi10Mg Aluminum is stiffer: Young's modulus 72 GPa against 2.3 GPa for Plastic ABS (bulk/injection), so the same part in DMLS AlSi10Mg Aluminum deflects less under the same load.
Which is lighter for the same job, DMLS AlSi10Mg Aluminum or Plastic ABS (bulk/injection)?
For the same stiffness or strength: DMLS AlSi10Mg Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; Plastic ABS (bulk/injection) is lighter for a strong panel or plate.
| Part that must be | DMLS AlSi10Mg Aluminum | Plastic ABS (bulk/injection) |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 12.2x heavier |
| Stiff beam (bending) | lighter | 2.18x heavier |
| Stiff panel or plate | lighter | 23% heavier |
| Strong rod or tie | lighter | 2.34x heavier |
| Strong beam | lighter | 29% heavier |
| Strong panel or plate | 5% heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, DMLS AlSi10Mg Aluminum or Plastic ABS (bulk/injection)?
DMLS AlSi10Mg Aluminum conducts heat better: 110 W/m·K against 0.17 W/m·K for Plastic ABS (bulk/injection).
Which expands less with temperature?
DMLS AlSi10Mg Aluminum expands less: 20 µm/m·K against 95 µm/m·K for Plastic ABS (bulk/injection).
Related comparisons
- DMLS AlSi10Mg Aluminum vs. Aluminum
- DMLS AlSi10Mg Aluminum vs. Aluminum 6061-T6
- DMLS AlSi10Mg Aluminum vs. Aluminum 2024-T351
- DMLS AlSi10Mg Aluminum vs. Aluminum 6063-T6
- Plastic ABS (bulk/injection) vs. FDM ASA
- Plastic ABS (bulk/injection) vs. FDM Polycarbonate
- Plastic ABS (bulk/injection) vs. Plastic ABS
- Plastic ABS (bulk/injection) vs. Plastic PETG