Materials / Compare
DMLS Ti-6Al-4V ELI Titanium vs. FDM Polycarbonate
Compare DMLS Ti-6Al-4V ELI Titanium vs. FDM Polycarbonate strength, stiffness, weight and thermal properties.
| Mechanical | DMLS Ti-6Al-4V ELI Titanium | FDM Polycarbonate |
|---|---|---|
| Yield strength | 1,100MPa120.6x stronger | 53.3MPa2 |
| Ultimate tensile strength | 1,270MPa123.8x stronger | 53.3MPa2 |
| Flexural strength | not sourced | 89.4MPa2 |
| Elongation at break | 8.7%1 | 9.2%2 |
| Young's modulus (stiffness) | same maker and process110GPa345.9x stiffer | 2.39GPa2 |
| Density | 4,400kg/m³1 | range1,180–1,200kg/m³2 |
| Strength to weight | 250kN·m/kg5.58x higher | 44.8kN·m/kg |
| Stiffness to weight | 25MN·m/kg12.4x higher | 2.01MN·m/kg |
| Poisson's ratio | wrought TIMETAL 6-40.3424 | base material0.385 |
| Shear modulus | 41GPa47.2x stiffer in shear | 0.867GPa |
| Bulk modulus | 116GPa34.9x higher | 3.33GPa |
| Speed of sound | 5,000m/s3.53x faster | 1,418m/s |
| Thermal | DMLS Ti-6Al-4V ELI Titanium | FDM Polycarbonate |
|---|---|---|
| Thermal conductivity | base material6.6W/m·K633x more heat through a fin | base material0.2W/m·K7 |
| Thermal expansion | mean 25-100 °C9µm/m·K87.22x less | base material65µm/m·K7 |
| 100 mm part over a 50 °C swing | 45µm growth7.22x less | 325µm growth |
| Specific heat | base material580J/kg·K6 | not sourced |
| Heats up and cools (diffusivity) | 2.59mm²/s | not sourced |
| Thermal shock resistance | 4,825W/m114x more resistant | 42.5W/m |
| Melting point | melting range1,630–1,650°C4 | not sourced |
| Glass transition | not sourced | 108°C2 |
| Max service temperature | not sourced | HDT 0.455 MPa105°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources8 documents: EOS GmbH, UltiMaker, TIMET, Covestro
- DMLS Ti-6Al-4V ELI Titanium
- EOS Titanium Ti64ELI (powder 9011-0040; ASTM F136/F3001, i.e. Grade 23) on EOS M400 SF, parameter set Ti64ELI_030_FlexM400_100, 30 µm, as built; ISO 6892-1 A14
- FDM Polycarbonate
- Ultimaker PC, 3D-printed specimens, XY (flat); Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS (file v5.00), April 20, 2022.
- 1EOS Titanium Ti64ELI Material Data Sheet, M 290 and M 400EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Yield strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Ultimate tensile strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Elongation at break: typical at break, as built (M400)DMLS Ti-6Al-4V ELI Titanium · Density: typical part density (ISO 3369), M400
- 2Ultimaker PC Technical Data Sheet, v5.00UltiMakerarchived copyFDM Polycarbonate · Yield strength: typicalFDM Polycarbonate · Ultimate tensile strength: typical, peak stress (= stress at yield)FDM Polycarbonate · Flexural strength: typicalFDM Polycarbonate · Elongation at break: typicalFDM Polycarbonate · Young's modulus (stiffness): typicalFDM Polycarbonate · Density: rangeFDM Polycarbonate · Glass transition: typicalFDM Polycarbonate · Max service temperature: HDT 0.455 MPa (printed specimens)
- 3EOS Titanium Ti64 Material Data Sheet, M 290 (2022)EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Young's modulus (stiffness): same maker and process, sibling grade: EOS Titanium Ti64 (Grade 5) on EOS M 290, as built, XY and Z, typical
- 4TIMETAL 6-4 PropertiesTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Poisson's ratio: wrought TIMETAL 6-4 (TIMET measurement, mean of 10); composition-level, not DMLS-measuredDMLS Ti-6Al-4V ELI Titanium · Melting point: melting range, wrought TIMETAL 6-4 (composition-level)
- 5Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyFDM Polycarbonate · Poisson's ratio: base material: polycarbonate family typical (Covestro Part and Mold Design guide, Table 3-1)
- 6TIMETAL 6-4 Data SheetTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal conductivity: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °CDMLS Ti-6Al-4V ELI Titanium · Specific heat: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °C
- 7Makrolon 2405 Technical Data SheetCovestroFDM Polycarbonate · Thermal conductivity: base material: Covestro Makrolon 2405 injection-molding PC, typical, through-plane, 23 °CFDM Polycarbonate · Thermal expansion: base material: Covestro Makrolon 2405 injection-molding PC, typical, 23-55 °C, parallel
- 8EOS Titanium Ti64 Grade 23 Material Data SheetEOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal expansion: mean 25-100 °C, ASTM E228; EOS Ti64 Grade 23 (=ELI) on EOS M 290 40 µm; condition not stated (sheet's mechanical data are heat treated)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS Ti-6Al-4V ELI Titanium and FDM Polycarbonate are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS Ti-6Al-4V ELI Titanium stronger than FDM Polycarbonate?
DMLS Ti-6Al-4V ELI Titanium is stronger: its yield strength is 1,100 MPa against 53.3 MPa for FDM Polycarbonate (20.6x).
Which is lighter, DMLS Ti-6Al-4V ELI Titanium or FDM Polycarbonate?
FDM Polycarbonate is lighter: 1,190 kg/m³ against 4,400 kg/m³ for DMLS Ti-6Al-4V ELI Titanium.
Which is stiffer, DMLS Ti-6Al-4V ELI Titanium or FDM Polycarbonate?
DMLS Ti-6Al-4V ELI Titanium is stiffer: Young's modulus 110 GPa against 2.39 GPa for FDM Polycarbonate, so the same part in DMLS Ti-6Al-4V ELI Titanium deflects less under the same load.
Which is lighter for the same job, DMLS Ti-6Al-4V ELI Titanium or FDM Polycarbonate?
For the same stiffness or strength: DMLS Ti-6Al-4V ELI Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate; FDM Polycarbonate is lighter for a stiff panel or plate.
| Part that must be | DMLS Ti-6Al-4V ELI Titanium | FDM Polycarbonate |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 12.4x heavier |
| Stiff beam (bending) | lighter | 1.83x heavier |
| Stiff panel or plate | 3% heavier | lighter |
| Strong rod or tie | lighter | 5.58x heavier |
| Strong beam | lighter | 2.03x heavier |
| Strong panel or plate | lighter | 23% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, DMLS Ti-6Al-4V ELI Titanium or FDM Polycarbonate?
DMLS Ti-6Al-4V ELI Titanium conducts heat better: 6.6 W/m·K against 0.2 W/m·K for FDM Polycarbonate.
Which expands less with temperature?
DMLS Ti-6Al-4V ELI Titanium expands less: 9 µm/m·K against 65 µm/m·K for FDM Polycarbonate.
Related comparisons
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium Ti-6Al-4V
- DMLS Ti-6Al-4V ELI Titanium vs. Stainless Steel 17-4PH
- DMLS Ti-6Al-4V ELI Titanium vs. Steel AISI 4340
- FDM Polycarbonate vs. Plastic Nylon
- FDM Polycarbonate vs. SLA Resin Standard
- FDM Polycarbonate vs. Plastic Polycarbonate
- FDM Polycarbonate vs. Plastic ABS (bulk/injection)