Materials / Compare
DMLS Ti-6Al-4V ELI Titanium vs. Plastic PEEK
Compare DMLS Ti-6Al-4V ELI Titanium vs. Plastic PEEK strength, stiffness, weight and thermal properties.
| Mechanical | DMLS Ti-6Al-4V ELI Titanium | Plastic PEEK |
|---|---|---|
| Yield strength | 1,100MPa111.2x stronger | 98MPa2 |
| Ultimate tensile strength | 1,270MPa1 | not stated (yield given) |
| Compressive strength | not sourced | 125MPa2 |
| Flexural strength | not sourced | 165MPa2 |
| Elongation at break | 8.7%1 | 25%22.87x more ductile |
| Young's modulus (stiffness) | same maker and process110GPa327.5x stiffer | 4GPa2 |
| Density | 4,400kg/m³1 | 1,300kg/m³23.38x lighter |
| Strength to weight | 250kN·m/kg3.32x higher | 75.4kN·m/kg |
| Stiffness to weight | 25MN·m/kg8.13x higher | 3.08MN·m/kg |
| Poisson's ratio | wrought TIMETAL 6-40.3424 | 0.385 |
| Shear modulus | 41GPa28.3x stiffer in shear | 1.45GPa |
| Bulk modulus | 116GPa20.9x higher | 5.56GPa |
| Speed of sound | 5,000m/s2.85x faster | 1,754m/s |
| Thermal | DMLS Ti-6Al-4V ELI Titanium | Plastic PEEK |
|---|---|---|
| Thermal conductivity | base material6.6W/m·K622.8x more heat through a fin | 0.29W/m·K2 |
| Thermal expansion | mean 25-100 °C9µm/m·K76.11x less | 55µm/m·K2 |
| 100 mm part over a 50 °C swing | 45µm growth6.11x less | 275µm growth |
| Specific heat | base material580J/kg·K6 | 2,200J/kg·K83.79x higher |
| Heats up and cools (diffusivity) | 2.59mm²/s25.5x faster | 0.101mm²/s |
| Thermal shock resistance | 4,825W/m60.2x more resistant | 80.1W/m |
| Melting point | melting range1,630–1,650°C4 | 343°C2 |
| Glass transition | not sourced | onset143°C2 |
| Max service temperature | not sourced | UL 746B RTI240°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources8 documents: EOS GmbH, Victrex, TIMET
- DMLS Ti-6Al-4V ELI Titanium
- EOS Titanium Ti64ELI (powder 9011-0040; ASTM F136/F3001, i.e. Grade 23) on EOS M400 SF, parameter set Ti64ELI_030_FlexM400_100, 30 µm, as built; ISO 6892-1 A14
- Plastic PEEK
- Victrex PEEK 450G (unreinforced, injection moulded), Victrex TDS rev. March 2026; Poisson from Victrex fluid-management flyer (2020-07)
- 1EOS Titanium Ti64ELI Material Data Sheet, M 290 and M 400EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Yield strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Ultimate tensile strength: typical, as built, average of horizontal + vertical (M400)DMLS Ti-6Al-4V ELI Titanium · Elongation at break: typical at break, as built (M400)DMLS Ti-6Al-4V ELI Titanium · Density: typical part density (ISO 3369), M400
- 2VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
- 3EOS Titanium Ti64 Material Data Sheet, M 290 (2022)EOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Young's modulus (stiffness): same maker and process, sibling grade: EOS Titanium Ti64 (Grade 5) on EOS M 290, as built, XY and Z, typical
- 4TIMETAL 6-4 PropertiesTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Poisson's ratio: wrought TIMETAL 6-4 (TIMET measurement, mean of 10); composition-level, not DMLS-measuredDMLS Ti-6Al-4V ELI Titanium · Melting point: melting range, wrought TIMETAL 6-4 (composition-level)
- 5VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
- 6TIMETAL 6-4 Data SheetTIMETarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal conductivity: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °CDMLS Ti-6Al-4V ELI Titanium · Specific heat: base material: wrought Ti-6Al-4V / 6-4 ELI (TIMET datasheet), 20 °C
- 7EOS Titanium Ti64 Grade 23 Material Data SheetEOS GmbHarchived copyDMLS Ti-6Al-4V ELI Titanium · Thermal expansion: mean 25-100 °C, ASTM E228; EOS Ti64 Grade 23 (=ELI) on EOS M 290 40 µm; condition not stated (sheet's mechanical data are heat treated)
- 8VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS Ti-6Al-4V ELI Titanium is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS Ti-6Al-4V ELI Titanium stronger than Plastic PEEK?
DMLS Ti-6Al-4V ELI Titanium is stronger: its yield strength is 1,100 MPa against 98 MPa for Plastic PEEK (11.2x).
Which is lighter, DMLS Ti-6Al-4V ELI Titanium or Plastic PEEK?
Plastic PEEK is lighter: 1,300 kg/m³ against 4,400 kg/m³ for DMLS Ti-6Al-4V ELI Titanium.
Which is stiffer, DMLS Ti-6Al-4V ELI Titanium or Plastic PEEK?
DMLS Ti-6Al-4V ELI Titanium is stiffer: Young's modulus 110 GPa against 4 GPa for Plastic PEEK, so the same part in DMLS Ti-6Al-4V ELI Titanium deflects less under the same load.
Which is lighter for the same job, DMLS Ti-6Al-4V ELI Titanium or Plastic PEEK?
For the same stiffness or strength: DMLS Ti-6Al-4V ELI Titanium is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam; Plastic PEEK is lighter for a stiff panel or plate, strong panel or plate.
| Part that must be | DMLS Ti-6Al-4V ELI Titanium | Plastic PEEK |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 8.13x heavier |
| Stiff beam (bending) | lighter | 1.55x heavier |
| Stiff panel or plate | 12% heavier | lighter |
| Strong rod or tie | lighter | 3.32x heavier |
| Strong beam | lighter | 48% heavier |
| Strong panel or plate | 1% heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS Ti-6Al-4V ELI Titanium or Plastic PEEK?
Plastic PEEK stretches further before it breaks: 25% elongation at break against 8.7% for DMLS Ti-6Al-4V ELI Titanium.
Thermal
Which conducts heat better, DMLS Ti-6Al-4V ELI Titanium or Plastic PEEK?
DMLS Ti-6Al-4V ELI Titanium conducts heat better: 6.6 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
DMLS Ti-6Al-4V ELI Titanium expands less: 9 µm/m·K against 55 µm/m·K for Plastic PEEK.
Related comparisons
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium
- DMLS Ti-6Al-4V ELI Titanium vs. Titanium Ti-6Al-4V
- DMLS Ti-6Al-4V ELI Titanium vs. Stainless Steel 17-4PH
- DMLS Ti-6Al-4V ELI Titanium vs. Steel AISI 4340
- Plastic PEEK vs. Plastic Nylon PA6
- Plastic PEEK vs. FDM PAHT-CF
- Plastic PEEK vs. Plastic PMMA
- Plastic PEEK vs. Plastic Nylon PA66