Materials / Compare
Drywall vs. DMLS 17-4PH Stainless Steel Compare Drywall vs. DMLS 17-4PH Stainless Steel strength, stiffness, weight and thermal properties.
Change either side
Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless 304 Stainless 316 Stainless 303 Stainless 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall Drywall Natural Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA Rubber Wood Aluminum Aluminum 6061-T6 Aluminum 7075-T6 Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Steel Steel AISI 1018 Steel AISI 1045 Steel AISI 4340 Steel A992 Iron Titanium Titanium Ti-6Al-4V Stainless 304 Stainless 316 Stainless 303 Stainless 17-4PH Brass C360 Brass C260 Copper C110 Glass Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Standard SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Concrete Brick Plywood Drywall DMLS 17-4PH Stainless Steel 3D printed metal (DMLS) Try it on a partA sample part to run stress or thermal on, free in your browser Open in LessCAD Open in LessCAD Mechanical Yield strength not given (tensile used) 861 MPa source mean, as built, horizontal (N=72) Ultimate tensile strength 1–2 MPa source ambient range reported in review (Australian studies) 886 MPa source mean, as built, horizontal (N=72) Compressive strength 2.4 MPa source typical, 70 F / 50% RH not sourced Elongation at break not sourced 19.9 % source mean at break, as built, horizontal Young's modulus (stiffness) 1–2 GPa source ambient range reported in review (Australian studies) 197 GPa source base material: wrought 17-4 PH, Condition H 900 (Cleveland-Cliffs) Density not sourced 7,790 kg/m³ source mean part density (ISO 3369) Strength to weight not sourced 110 kN·m/kg Stiffness to weight not sourced 25.3 MN·m/kg Poisson's ratio not sourced 0.272 source base material: wrought 17-4 PH, all conditions (Cleveland-Cliffs) Shear modulus not sourced 77.4 GPa Bulk modulus not sourced 144 GPa Speed of sound not sourced 5,029 m/s Thermal Thermal conductivity not sourced 17.9 W/m·K source base material: wrought 17-4 PH, Condition H 900, at 149 °C (Cleveland-Cliffs) Thermal expansion 16.7 µm/m·K source typical, unrestrained, 3.3-32 C 10.4 µm/m·K source mean 25-100 °C, ASTM E228, AFTER atmospheric heat treatment (as-built value not published) 100 mm part over a 50 °C swing 83.5 µm growth 52 µm growth 1.61x less Specific heat 1,090 J/kg·K source typical (from ASHRAE Handbook of Fundamentals, per GA) 460 J/kg·K source base material: wrought 17-4 PH, Condition A, 0-100 °C (Cleveland-Cliffs) Heats up and cools (diffusivity) not sourced 5 mm²/s Thermal shock resistance not sourced 5,474 W/m Max service temperature 52 °C source manufacturer sustained-exposure limit not sourced Values for 1/2 in. (12.7 mm) regular gypsum board (ASTM C1396), Gypsum Association GA-235-2019 typical/minimum properties; tensile and E from USDA FPL-co-authored review; service limit from USG Sheetrock 1/2 in. submittal EOS StainlessSteel 17-4PH IndustryLine (powder 9011-0041), EOS M 290, 40 µm, default job 17-4PH_040_StainlessM291_100, as built, horizontal; ISO 6892 & ASTM E8M
Every value links to the document that states it. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS 17-4PH Stainless Steel is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions Is Drywall stronger than DMLS 17-4PH Stainless Steel? DMLS 17-4PH Stainless Steel is stronger: its yield strength is 861 MPa against tensile strength 1.5 MPa for Drywall (574x).
Which is stiffer, Drywall or DMLS 17-4PH Stainless Steel? DMLS 17-4PH Stainless Steel is stiffer: Young's modulus 197 GPa against 1.5 GPa for Drywall, so the same part in DMLS 17-4PH Stainless Steel deflects less under the same load.
Which expands less with temperature? DMLS 17-4PH Stainless Steel expands less: 10.4 µm/m·K against 16.7 µm/m·K for Drywall.
Among 59 materials 1k 10k 0.1 1 10 100 Density (kg/m³) Young's modulus (GPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Aluminum Steel Iron Titanium Steel AISI 1018 Stainless 304 Stainless 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless 303 Stainless 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Brass C260 Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel DMLS 17-4PH Stainless Steel Stiffness against density 1k 10k 10 100 1k Density (kg/m³) Yield strength (MPa) Plastic PLA Plastic PETG Plastic ABS Plastic TPU Plastic Nylon Rubber Aluminum Steel Iron Titanium Steel AISI 1018 Stainless 304 Stainless 316 Aluminum 6061-T6 Aluminum 7075-T6 Brass C360 Copper C110 Glass Steel AISI 1045 Steel AISI 4340 Steel A992 Stainless 303 Stainless 17-4PH Aluminum 2024-T351 Aluminum 5052-H32 Aluminum 7050-T7451 Titanium Ti-6Al-4V Brass C260 Nickel Inconel 718 Magnesium AZ31B-H24 Zinc Zamak 3 Plastic ABS (bulk/injection) Plastic Polycarbonate Plastic POM/Acetal Plastic Nylon PA6 Plastic Nylon PA66 Plastic PEEK Plastic PTFE Plastic UHMWPE Plastic HDPE Plastic Polypropylene Plastic PMMA FDM ASA FDM Polycarbonate FDM PAHT-CF FDM HIPS SLA Resin Tough 2000 SLA Resin Elastic 50A SLS PA12 Nylon DMLS AlSi10Mg Aluminum DMLS Ti-6Al-4V ELI Titanium DMLS 316L Stainless Steel Brick DMLS 17-4PH Stainless Steel Strength against density