Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Plastic Nylon PA6
BASF Ultramid B3S (PA6, unreinforced injection-moulding grade), Product Information 02/2026, dry values (ISO methods)
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon PA6 · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Plastic Nylon PA6?
Plastic Nylon PA6 is stronger: its yield strength is 90 MPa against tensile strength 18.4 MPa for FDM HIPS (4.89x).
Which is lighter, FDM HIPS or Plastic Nylon PA6?
FDM HIPS is lighter: 1,023 kg/m³ against 1,130 kg/m³ for Plastic Nylon PA6.
Which is stiffer, FDM HIPS or Plastic Nylon PA6?
Plastic Nylon PA6 is stiffer: Young's modulus 3.5 GPa against 1.59 GPa for FDM HIPS, so the same part in Plastic Nylon PA6 deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Plastic Nylon PA6?
For the same stiffness or strength: Plastic Nylon PA6 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM HIPS
Plastic Nylon PA6
Stiff rod or tie (tension)
2x heavier
lighter
Stiff beam (bending)
34% heavier
lighter
Stiff panel or plate
18% heavier
lighter
Strong rod or tie
4.43x heavier
lighter
Strong beam
2.61x heavier
lighter
Strong panel or plate
2x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Plastic Nylon PA6?
Plastic Nylon PA6 stretches further before it breaks: 10% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Plastic Nylon PA6?
Plastic Nylon PA6 conducts heat better: 0.33 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
FDM HIPS expands less: 80 µm/m·K against 102 µm/m·K for Plastic Nylon PA6.