Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
SLA Resin Standard
Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
3
Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS and SLA Resin Standard are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than SLA Resin Standard?
SLA Resin Standard is stronger: its tensile strength is 60 MPa against 18.4 MPa for FDM HIPS (3.26x).
Which is lighter, FDM HIPS or SLA Resin Standard?
FDM HIPS is lighter: 1,023 kg/m³ against 1,210 kg/m³ for SLA Resin Standard.
Which is stiffer, FDM HIPS or SLA Resin Standard?
SLA Resin Standard is stiffer: Young's modulus 2.75 GPa against 1.59 GPa for FDM HIPS, so the same part in SLA Resin Standard deflects less under the same load.
Which is lighter for the same job, FDM HIPS or SLA Resin Standard?
For the same stiffness or strength: SLA Resin Standard is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM HIPS
SLA Resin Standard
Stiff rod or tie (tension)
46% heavier
lighter
Stiff beam (bending)
11% heavier
lighter
Stiff panel or plate
2% heavier
lighter
Strong rod or tie
2.76x heavier
lighter
Strong beam
1.86x heavier
lighter
Strong panel or plate
1.53x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or SLA Resin Standard?
SLA Resin Standard stretches further before it breaks: 8% elongation at break against 1.4% for FDM HIPS.
Thermal
Which handles higher temperatures, FDM HIPS or SLA Resin Standard?
FDM HIPS does: 86 °C against 59 °C for SLA Resin Standard, both HDT 1.8 MPa.
Which conducts heat better, FDM HIPS or SLA Resin Standard?
SLA Resin Standard conducts heat better: 0.54 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
FDM HIPS expands less: 80 µm/m·K against 114 µm/m·K for SLA Resin Standard.