Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Stainless Steel 17-4PH
Cleveland-Cliffs 17-4 PH, Condition H 900, sheet/strip, transverse (Product Data Bulletin, May 2021)
1
17-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 17-4PH · Yield strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Ultimate tensile strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Elongation at break: typical, transverse, in 2 in. (50.8 mm)Stainless Steel 17-4PH · Young's modulus (stiffness): H 900Stainless Steel 17-4PH · Density: H 900Stainless Steel 17-4PH · Poisson's ratio: H 900 (column)Stainless Steel 17-4PH · Thermal conductivity: at 149 °C (300 °F), H 900Stainless Steel 17-4PH · Thermal expansion: mean, 21–93 °C (70–200 °F), H 900Stainless Steel 17-4PH · Specific heat: mean, 0–100 °C, H 900Stainless Steel 17-4PH · Max service temperature: strength-retention limit (not oxidation)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stronger: its yield strength is 1,275 MPa against tensile strength 18.4 MPa for FDM HIPS (69.3x).
Which is lighter, FDM HIPS or Stainless Steel 17-4PH?
FDM HIPS is lighter: 1,023 kg/m³ against 7,800 kg/m³ for Stainless Steel 17-4PH.
Which is stiffer, FDM HIPS or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stiffer: Young's modulus 197 GPa against 1.59 GPa for FDM HIPS, so the same part in Stainless Steel 17-4PH deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Stainless Steel 17-4PH?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate; Stainless Steel 17-4PH is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM HIPS
Stainless Steel 17-4PH
Stiff rod or tie (tension)
16.3x heavier
lighter
Stiff beam (bending)
46% heavier
lighter
Stiff panel or plate
lighter
1.53x heavier
Strong rod or tie
9.09x heavier
lighter
Strong beam
2.21x heavier
lighter
Strong panel or plate
9% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Stainless Steel 17-4PH?
Stainless Steel 17-4PH stretches further before it breaks: 9% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Stainless Steel 17-4PH?
Stainless Steel 17-4PH conducts heat better: 17.9 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Stainless Steel 17-4PH expands less: 10.8 µm/m·K against 80 µm/m·K for FDM HIPS.