Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: ATI, BASF Forward AM, Steel Construction Institute, INEOS Styrolution
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against tensile strength 18.4 MPa for FDM HIPS (14.4x).
Which is lighter, FDM HIPS or Stainless Steel 316?
FDM HIPS is lighter: 1,023 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, FDM HIPS or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 1.59 GPa for FDM HIPS, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Stainless Steel 316?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie.
Part that must be
FDM HIPS
Stainless Steel 316
Stiff rod or tie (tension)
16.1x heavier
lighter
Stiff beam (bending)
43% heavier
lighter
Stiff panel or plate
lighter
1.57x heavier
Strong rod or tie
1.84x heavier
lighter
Strong beam
lighter
33% heavier
Strong panel or plate
lighter
2.07x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Stainless Steel 316 expands less: 16.5 µm/m·K against 80 µm/m·K for FDM HIPS.