Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Special Metals, Outokumpu, Steel Construction Institute, Carpenter Technology
Nickel Inconel 718
INCONEL alloy 718, standard grade, 1750 °F/1 hr anneal + 1325 °F/8 hr F.C. to 1150 °F aged; Special Metals bulletin SMC-045 typical values
Stainless Steel 303
1.4305 / UNS S30300, Outokumpu typical values (hot rolled, solution annealed) from 'Steel Grades, Properties and Global Standards'; max service from Carpenter CarTech 303 datasheet
1
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
2
Steel Grades, Properties and Global StandardsOutokumpuarchived copyStainless Steel 303 · Yield strength: Outokumpu typical (product P = hot rolled plate, transverse)Stainless Steel 303 · Ultimate tensile strength: Outokumpu typicalStainless Steel 303 · Elongation at break: Outokumpu typical, A5Stainless Steel 303 · Young's modulus (stiffness): at RT (Table 12)Stainless Steel 303 · Density: at RTStainless Steel 303 · Thermal conductivity: at RTStainless Steel 303 · Thermal expansion: mean, 20–100 °CStainless Steel 303 · Specific heat: at RT
3
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 303 · Poisson's ratio: design value (structural stainless steels)
4
Carpenter Stainless Type 303 Data SheetCarpenter Technologyarchived copyStainless Steel 303 · Max service temperature: continuous, scaling limit
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Nickel Inconel 718 stronger than Stainless Steel 303?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 275 MPa for Stainless Steel 303 (4.39x).
Which is lighter, Nickel Inconel 718 or Stainless Steel 303?
Stainless Steel 303 is lighter: 7,900 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, Nickel Inconel 718 or Stainless Steel 303?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 200 GPa for Stainless Steel 303, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Nickel Inconel 718 or Stainless Steel 303?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a strong rod or tie, strong beam, strong panel or plate; Stainless Steel 303 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate.
Part that must be
Nickel Inconel 718
Stainless Steel 303
Stiff rod or tie (tension)
4% heavier
lighter
Stiff beam (bending)
4% heavier
lighter
Stiff panel or plate
4% heavier
lighter
Strong rod or tie
lighter
4.22x heavier
Strong beam
lighter
2.58x heavier
Strong panel or plate
lighter
2.01x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Nickel Inconel 718 or Stainless Steel 303?
Stainless Steel 303 stretches further before it breaks: 35% elongation at break against 20% for Nickel Inconel 718.
Thermal
Which handles higher temperatures, Nickel Inconel 718 or Stainless Steel 303?
Stainless Steel 303 does: 871 °C against 704 °C for Nickel Inconel 718.
Which conducts heat better, Nickel Inconel 718 or Stainless Steel 303?
Stainless Steel 303 conducts heat better: 15 W/m·K against 11.4 W/m·K for Nickel Inconel 718.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 16 µm/m·K for Stainless Steel 303.