Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
PLEXIGLAS GS and XT Technical Information (Ref. No. 211-1)Röhmarchived copyPlastic PMMA · Ultimate tensile strength: typical, 23 °CPlastic PMMA · Compressive strength: compressive yield stress, typicalPlastic PMMA · Flexural strength: typicalPlastic PMMA · Elongation at break: typicalPlastic PMMA · Young's modulus (stiffness): typical, short-termPlastic PMMA · Density: typicalPlastic PMMA · Poisson's ratio: typicalPlastic PMMA · Thermal conductivity: typicalPlastic PMMA · Thermal expansion: 0-50 °CPlastic PMMA · Specific heat: typicalPlastic PMMA · Max service temperature: max. permanent service temperature
3
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic PMMA stronger than Zinc Zamak 3?
Zinc Zamak 3 is stronger: its yield strength is 221 MPa against tensile strength 80 MPa for Plastic PMMA (2.76x).
Which is lighter, Plastic PMMA or Zinc Zamak 3?
Plastic PMMA is lighter: 1,190 kg/m³ against 6,600 kg/m³ for Zinc Zamak 3.
Which is stiffer, Plastic PMMA or Zinc Zamak 3?
Zinc Zamak 3 is stiffer: Young's modulus 85.5 GPa against 3.3 GPa for Plastic PMMA, so the same part in Zinc Zamak 3 deflects less under the same load.
Which is lighter for the same job, Plastic PMMA or Zinc Zamak 3?
For the same stiffness or strength: Plastic PMMA is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Zinc Zamak 3 is lighter for a stiff rod or tie (tension).
Part that must be
Plastic PMMA
Zinc Zamak 3
Stiff rod or tie (tension)
4.67x heavier
lighter
Stiff beam (bending)
lighter
9% heavier
Stiff panel or plate
lighter
1.87x heavier
Strong rod or tie
lighter
2.01x heavier
Strong beam
lighter
2.82x heavier
Strong panel or plate
lighter
3.34x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PMMA or Zinc Zamak 3?
Zinc Zamak 3 stretches further before it breaks: 10% elongation at break against 5.5% for Plastic PMMA.
Thermal
Which conducts heat better, Plastic PMMA or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 0.19 W/m·K for Plastic PMMA.
Which expands less with temperature?
Zinc Zamak 3 expands less: 27.4 µm/m·K against 70 µm/m·K for Plastic PMMA.