Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Celanese GUR 4120 (avg. molecular weight 4.7x10^6 g/mol), typical values on compression-molded specimens; CTE and thermal conductivity from Celanese's generic UHMWPE guide (grade not named)
Zinc Zamak 3
Zamak 3 (ASTM B86 die cast), Nathan Trotter (zinc alloy producer) technical data sheet, typical values
1
GUR UHMW-PE Overview (GUR-015)CelanesePlastic UHMWPE · Yield strength: typical, tensile stress at yield ISO 527, 50 mm/minPlastic UHMWPE · Ultimate tensile strength: typical, tensile stress at break ISO 527, 50 mm/minPlastic UHMWPE · Elongation at break: typical, nominal elongation at break ISO 527Plastic UHMWPE · Young's modulus (stiffness): typical, tensile modulus ISO 527, 1 mm/minPlastic UHMWPE · Density: typicalPlastic UHMWPE · Melting point: DSC 10 K/minPlastic UHMWPE · Max service temperature: recommended max constant operating temperature
Zinc Die Casting Properties Guide (2012)Eastern AlloysZinc Zamak 3 · Poisson's ratio: typical, Zamak 3 hot-chamber die cast
4
GUR UHMW-PE Polymer Guide (GUR-003)Celanesearchived copyPlastic UHMWPE · Thermal conductivity: typical, unfilled (narrative value, generic Celanese UHMWPE)Plastic UHMWPE · Thermal expansion: typical, 20 to 100 °C (generic Celanese UHMWPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic UHMWPE stronger than Zinc Zamak 3?
Zinc Zamak 3 is stronger: its yield strength is 221 MPa against 20 MPa for Plastic UHMWPE (11.1x).
Which is lighter, Plastic UHMWPE or Zinc Zamak 3?
Plastic UHMWPE is lighter: 930 kg/m³ against 6,600 kg/m³ for Zinc Zamak 3.
Which is stiffer, Plastic UHMWPE or Zinc Zamak 3?
Zinc Zamak 3 is stiffer: Young's modulus 85.5 GPa against 0.66 GPa for Plastic UHMWPE, so the same part in Zinc Zamak 3 deflects less under the same load.
Which is lighter for the same job, Plastic UHMWPE or Zinc Zamak 3?
For the same stiffness or strength: Plastic UHMWPE is lighter for a stiff panel or plate, strong beam, strong panel or plate; Zinc Zamak 3 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie.
Part that must be
Plastic UHMWPE
Zinc Zamak 3
Stiff rod or tie (tension)
18.3x heavier
lighter
Stiff beam (bending)
1.6x heavier
lighter
Stiff panel or plate
lighter
40% heavier
Strong rod or tie
1.56x heavier
lighter
Strong beam
lighter
43% heavier
Strong panel or plate
lighter
2.13x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic UHMWPE or Zinc Zamak 3?
Plastic UHMWPE stretches further before it breaks: 465% elongation at break against 10% for Zinc Zamak 3.
Thermal
Which conducts heat better, Plastic UHMWPE or Zinc Zamak 3?
Zinc Zamak 3 conducts heat better: 113 W/m·K against 0.4 W/m·K for Plastic UHMWPE.
Which expands less with temperature?
Zinc Zamak 3 expands less: 27.4 µm/m·K against 200 µm/m·K for Plastic UHMWPE.