Materials / Compare
SLA Resin Standard vs. DMLS 17-4PH Stainless Steel
Compare SLA Resin Standard vs. DMLS 17-4PH Stainless Steel strength, stiffness, weight and thermal properties.
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|---|---|
| Mechanical | ||
| Yield strength | not given (tensile used) | 861MPasourcemean, as built, horizontal (N=72) |
| Ultimate tensile strength | 60MPasourcetypical | 886MPasourcemean, as built, horizontal (N=72) |
| Flexural strength | 105MPasourcetypical | not sourced |
| Elongation at break | 8%sourcetypical | 19.9%sourcemean at break, as built, horizontal |
| Young's modulus (stiffness) | 2.75GPasourcetypical | 197GPasourcebase material: wrought 17-4 PH, Condition H 900 (Cleveland-Cliffs) |
| Density | not sourced | 7,790kg/m³sourcemean part density (ISO 3369) |
| Strength to weight | not sourced | 110kN·m/kg |
| Stiffness to weight | not sourced | 25.3MN·m/kg |
| Poisson's ratio | not sourced | 0.272sourcebase material: wrought 17-4 PH, all conditions (Cleveland-Cliffs) |
| Shear modulus | not sourced | 77.4GPa |
| Bulk modulus | not sourced | 144GPa |
| Speed of sound | not sourced | 5,029m/s |
| Thermal | ||
| Thermal conductivity | not sourced | 17.9W/m·Ksourcebase material: wrought 17-4 PH, Condition H 900, at 149 °C (Cleveland-Cliffs) |
| Thermal expansion | not sourced | 10.4µm/m·Ksourcemean 25-100 °C, ASTM E228, AFTER atmospheric heat treatment (as-built value not published) |
| 100 mm part over a 50 °C swing | not sourced | 52µm growth |
| Specific heat | not sourced | 460J/kg·Ksourcebase material: wrought 17-4 PH, Condition A, 0-100 °C (Cleveland-Cliffs) |
| Heats up and cools (diffusivity) | not sourced | 5mm²/s |
| Thermal shock resistance | not sourced | 5,474W/m |
| Max service temperature | 59°CsourceHDT 1.8 MPa | not sourced |
| Values for | Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated. | EOS StainlessSteel 17-4PH IndustryLine (powder 9011-0041), EOS M 290, 40 µm, default job 17-4PH_040_StainlessM291_100, as built, horizontal; ISO 6892 & ASTM E8M |
Every value links to the document that states it. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Standard and DMLS 17-4PH Stainless Steel are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Is SLA Resin Standard stronger than DMLS 17-4PH Stainless Steel?
DMLS 17-4PH Stainless Steel is stronger: its yield strength is 861 MPa against tensile strength 60 MPa for SLA Resin Standard (14.3x).
Which is stiffer, SLA Resin Standard or DMLS 17-4PH Stainless Steel?
DMLS 17-4PH Stainless Steel is stiffer: Young's modulus 197 GPa against 2.75 GPa for SLA Resin Standard, so the same part in DMLS 17-4PH Stainless Steel deflects less under the same load.
Among 59 materials
Related comparisons
- SLA Resin Standard vs. Plastic POM/Acetal
- SLA Resin Standard vs. Plastic Polycarbonate
- SLA Resin Standard vs. Plastic Nylon
- SLA Resin Standard vs. FDM Polycarbonate
- DMLS 17-4PH Stainless Steel vs. Steel AISI 4340
- DMLS 17-4PH Stainless Steel vs. Nickel Inconel 718
- DMLS 17-4PH Stainless Steel vs. Stainless 17-4PH
- DMLS 17-4PH Stainless Steel vs. Steel AISI 1045