Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Cleveland-Cliffs, Formlabs, Steel Construction Institute
SLA Resin Elastic 50A
Formlabs Elastic 50A Resin V2 (FLELCL02), TDS Rev. 01 24.01.2024; parts printed on Form 3, 100 µm, Elastic 50A V2 settings and post-processing; tensile on Die C specimens cut from printed sheets after 3+ h at 23 °C.
Stainless Steel 304
Type 304, annealed flat-rolled (Cleveland-Cliffs 304/304L Product Data Bulletin, May 2021); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
304/304L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 304 · Yield strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Ultimate tensile strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Elongation at break: typical, annealed, in 2 in. (50.8 mm)Stainless Steel 304 · Young's modulus (stiffness): typical, in tensionStainless Steel 304 · Density: typicalStainless Steel 304 · Thermal conductivity: at 100 °CStainless Steel 304 · Thermal expansion: mean, 0–100 °CStainless Steel 304 · Specific heat: mean, 0–100 °CStainless Steel 304 · Melting point: melting rangeStainless Steel 304 · Max service temperature: continuous, oxidation (scaling) limit in air
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 304 · Poisson's ratio: design value (structural stainless steels)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLA Resin Elastic 50A is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is SLA Resin Elastic 50A stronger than Stainless Steel 304?
Stainless Steel 304 is stronger: its yield strength is 241 MPa against tensile strength 3.4 MPa for SLA Resin Elastic 50A (70.9x).
Which is lighter, SLA Resin Elastic 50A or Stainless Steel 304?
SLA Resin Elastic 50A is lighter: 1,010 kg/m³ against 8,030 kg/m³ for Stainless Steel 304.
Which is lighter for the same job, SLA Resin Elastic 50A or Stainless Steel 304?
For the same stiffness or strength: Stainless Steel 304 is lighter for a strong rod or tie, strong beam, strong panel or plate.
Part that must be
SLA Resin Elastic 50A
Stainless Steel 304
Strong rod or tie
8.92x heavier
lighter
Strong beam
2.15x heavier
lighter
Strong panel or plate
6% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, SLA Resin Elastic 50A or Stainless Steel 304?
SLA Resin Elastic 50A stretches further before it breaks: 160% elongation at break against 55% for Stainless Steel 304.