Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 2024-T351 · Poisson's ratio: typical (handbook physical constant), all tempers
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
5
Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Aluminum 2024-T351 stronger than Plastic Nylon?
Aluminum 2024-T351 is stronger: its yield strength is 324 MPa against 63.1 MPa for Plastic Nylon (5.13x).
Which is lighter, Aluminum 2024-T351 or Plastic Nylon?
Plastic Nylon is lighter: 1,140 kg/m³ against 2,770 kg/m³ for Aluminum 2024-T351.
Which is stiffer, Aluminum 2024-T351 or Plastic Nylon?
Aluminum 2024-T351 is stiffer: Young's modulus 73.1 GPa against 2.33 GPa for Plastic Nylon, so the same part in Aluminum 2024-T351 deflects less under the same load.
Which is lighter for the same job, Aluminum 2024-T351 or Plastic Nylon?
For the same stiffness or strength: Aluminum 2024-T351 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; Plastic Nylon is lighter for a strong panel or plate.
Part that must be
Aluminum 2024-T351
Plastic Nylon
Stiff rod or tie (tension)
lighter
12.9x heavier
Stiff beam (bending)
lighter
2.3x heavier
Stiff panel or plate
lighter
30% heavier
Strong rod or tie
lighter
2.11x heavier
Strong beam
lighter
22% heavier
Strong panel or plate
7% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Aluminum 2024-T351 or Plastic Nylon?
Aluminum 2024-T351 conducts heat better: 120 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Aluminum 2024-T351 expands less: 22.9 µm/m·K against 100 µm/m·K for Plastic Nylon.