Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
4
VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
5
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Plastic PEEK?
Brass C360 is stronger: its yield strength is 310 MPa against 98 MPa for Plastic PEEK (3.16x).
Which is lighter, Brass C360 or Plastic PEEK?
Plastic PEEK is lighter: 1,300 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Plastic PEEK?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 4 GPa for Plastic PEEK, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or Plastic PEEK?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension); Plastic PEEK is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
Plastic PEEK
Stiff rod or tie (tension)
lighter
3.69x heavier
Stiff beam (bending)
33% heavier
lighter
Stiff panel or plate
2.26x heavier
lighter
Strong rod or tie
2.07x heavier
lighter
Strong beam
3.03x heavier
lighter
Strong panel or plate
3.68x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Brass C360 or Plastic PEEK?
Brass C360 conducts heat better: 116 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
Brass C360 expands less: 20.5 µm/m·K against 55 µm/m·K for Plastic PEEK.