Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Copper Development Association, EOS GmbH, Wieland
Brass C360
C36000 free-cutting brass, H02 half-hard rod 1 in. section (20% cold work), copper.org typical values
SLS PA12 Nylon
EOS PA 2200 (PA12) Material Data Sheet, process parameter 'Balance' at 120 µm layer thickness, X orientation, dry (conditioned values not given). Live MDS status 04.10.2026, last changed 10.09.2026; PDF via ?topdf=... link on the same page.
PA 2200 Balance Material Data SheetEOS GmbHSLS PA12 Nylon · Ultimate tensile strength: typicalSLS PA12 Nylon · Elongation at break: typicalSLS PA12 Nylon · Young's modulus (stiffness): typicalSLS PA12 Nylon · Density: typicalSLS PA12 Nylon · Melting point: typicalSLS PA12 Nylon · Max service temperature: HDT 1.8 MPa, X orientation
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
SLS PA12 Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Brass C360 stronger than SLS PA12 Nylon?
Brass C360 is stronger: its yield strength is 310 MPa against tensile strength 48 MPa for SLS PA12 Nylon (6.46x).
Which is lighter, Brass C360 or SLS PA12 Nylon?
SLS PA12 Nylon is lighter: 930 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or SLS PA12 Nylon?
Brass C360 is stiffer: Young's modulus 96.5 GPa against 1.65 GPa for SLS PA12 Nylon, so the same part in Brass C360 deflects less under the same load.
Which is lighter for the same job, Brass C360 or SLS PA12 Nylon?
For the same stiffness or strength: Brass C360 is lighter for a stiff rod or tie (tension); SLS PA12 Nylon is lighter for a stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
SLS PA12 Nylon
Stiff rod or tie (tension)
lighter
6.4x heavier
Stiff beam (bending)
19% heavier
lighter
Stiff panel or plate
2.35x heavier
lighter
Strong rod or tie
41% heavier
lighter
Strong beam
2.63x heavier
lighter
Strong panel or plate
3.6x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or SLS PA12 Nylon?
Brass C360 stretches further before it breaks: 25% elongation at break against 18% for SLS PA12 Nylon.