Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
3
Wieland-K32 (Cu-ETP, C11000) Data SheetWielandarchived copyCopper C110 · Poisson's ratio: reference value at room temperature (Wieland-K32 = Cu-ETP = C11000, rolled products)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Copper C110 stronger than Nickel Inconel 718?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 69 MPa for Copper C110 (17.5x).
Which is lighter, Copper C110 or Nickel Inconel 718?
Nickel Inconel 718 is lighter: 8,221 kg/m³ against 8,913 kg/m³ for Copper C110.
Which is stiffer, Copper C110 or Nickel Inconel 718?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 117 GPa for Copper C110, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Copper C110 or Nickel Inconel 718?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Copper C110
Nickel Inconel 718
Stiff rod or tie (tension)
1.85x heavier
lighter
Stiff beam (bending)
42% heavier
lighter
Stiff panel or plate
30% heavier
lighter
Strong rod or tie
19x heavier
lighter
Strong beam
7.31x heavier
lighter
Strong panel or plate
4.53x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Copper C110 or Nickel Inconel 718?
Copper C110 stretches further before it breaks: 55% elongation at break against 20% for Nickel Inconel 718.
Thermal
Which conducts heat better, Copper C110 or Nickel Inconel 718?
Copper C110 conducts heat better: 391 W/m·K against 11.4 W/m·K for Nickel Inconel 718.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 16.9 µm/m·K for Copper C110.