Materials / Compare
DMLS AlSi10Mg Aluminum vs. Plastic POM/Acetal
Compare DMLS AlSi10Mg Aluminum vs. Plastic POM/Acetal strength, stiffness, weight and thermal properties.
| Mechanical | DMLS AlSi10Mg Aluminum | Plastic POM/Acetal |
|---|---|---|
| Yield strength | 270MPa13.91x stronger | 69MPa2 |
| Ultimate tensile strength | 450MPa16.52x stronger | 69MPa2 |
| Compressive strength | not sourced | 124MPa2 |
| Flexural strength | not sourced | 99MPa2 |
| Elongation at break | 10.2%1 | 75%27.35x more ductile |
| Young's modulus (stiffness) | 72GPa325.7x stiffer | 2.8GPa2 |
| Density | 2,670kg/m³4 | 1,420kg/m³51.88x lighter |
| Strength to weight | 101kN·m/kg2.08x higher | 48.6kN·m/kg |
| Stiffness to weight | 27MN·m/kg13.7x higher | 1.97MN·m/kg |
| Poisson's ratio | base material0.336 | 0.352 |
| Shear modulus | 27.1GPa26.1x stiffer in shear | 1.04GPa |
| Bulk modulus | 70.6GPa22.7x higher | 3.11GPa |
| Speed of sound | 5,193m/s3.7x faster | 1,404m/s |
| Thermal | DMLS AlSi10Mg Aluminum | Plastic POM/Acetal |
|---|---|---|
| Thermal conductivity | 110W/m·K1275x more heat through a fin | 0.4W/m·K2 |
| Thermal expansion | mean 25-100 °C20µm/m·K16.1x less | mean122µm/m·K2 |
| 100 mm part over a 50 °C swing | 100µm growth6.1x less | 610µm growth |
| Specific heat | base material963J/kg·K6 | average -18 to 100 °C1,465J/kg·K2 |
| Heats up and cools (diffusivity) | 42.8mm²/s222x faster | 0.192mm²/s |
| Thermal shock resistance | 13,819W/m263x more resistant | 52.5W/m |
| Melting point | not sourced | 175°C2 |
| Max service temperature | not sourced | HDT 1.8 MPa125°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources6 documents: EOS GmbH, DuPont, Renishaw, U.S. Department of Defense
- DMLS AlSi10Mg Aluminum
- EOS Aluminium AlSi10Mg (powder 9011-0024), EOS M 290 | 30 µm process (AlSi10Mg_FlexM291 2.01), as manufactured, horizontal; machined (turned) specimens, ISO 6892-1 B10
- Plastic POM/Acetal
- DuPont Delrin 100 acetal homopolymer, Table 2 'Typical Properties of Delrin Acetal Resins' (ASTM methods), Delrin Design Guide Module III hosted on delrin.com
- 1EOS Aluminium AlSi10Mg Material Data SheetEOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Yield strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Ultimate tensile strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Elongation at break: typical at break, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Thermal conductivity: typical, as manufactured, horizontal (ISO 22007-2)DMLS AlSi10Mg Aluminum · Thermal expansion: mean 25-100 °C, ASTM E228
- 2Delrin Acetal Resin Design Guide, Module IIIDuPontarchived copyPlastic POM/Acetal · Yield strength: typical (single ASTM D638 tensile strength)Plastic POM/Acetal · Ultimate tensile strength: typicalPlastic POM/Acetal · Compressive strength: compressive stress at 10% deformationPlastic POM/Acetal · Flexural strength: flexural yield strength, typicalPlastic POM/Acetal · Elongation at break: typicalPlastic POM/Acetal · Young's modulus (stiffness): typicalPlastic POM/Acetal · Poisson's ratio: typicalPlastic POM/Acetal · Thermal conductivity: typicalPlastic POM/Acetal · Thermal expansion: mean, 29 to 60 °CPlastic POM/Acetal · Specific heat: average -18 to 100 °C, Delrin acetal resins (not grade-specific)Plastic POM/Acetal · Melting point: crystalline melting pointPlastic POM/Acetal · Max service temperature: HDT 1.8 MPa (annealed)
- 3RenAM 500 Series Aluminium AlSi10Mg Material Data SheetRenishawDMLS AlSi10Mg Aluminum · Young's modulus (stiffness): same material and process, different machine maker: Renishaw RenAM 500, 30 µm, as built, horizontal (XY)
- 4EOS Aluminium AlSi10Mg Material Data Sheet, FlexLine, M 290 (2018)EOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Density: typical part density (ISO 3369), EOS M 290, AlSi10Mg_030_FlexM291 (30 µm)
- 5Delrin 100 Product Data SheetDuPontPlastic POM/Acetal · Density: typical (DuPont product information for Delrin 100 NC010; 'The data listed here fall within the normal range of product properties')
- 6MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseDMLS AlSi10Mg Aluminum · Poisson's ratio: base material: cast Al-Si-Mg alloy 359.0 (Al-9Si-0.6Mg, closest MIL-HDBK-5J alloy to AlSi10Mg / EN AC-43000)DMLS AlSi10Mg Aluminum · Specific heat: base material: cast Al-Si-Mg alloy 359.0 (MIL-HDBK-5J), at 100 °C
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS AlSi10Mg Aluminum is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS AlSi10Mg Aluminum stronger than Plastic POM/Acetal?
DMLS AlSi10Mg Aluminum is stronger: its yield strength is 270 MPa against 69 MPa for Plastic POM/Acetal (3.91x).
Which is lighter, DMLS AlSi10Mg Aluminum or Plastic POM/Acetal?
Plastic POM/Acetal is lighter: 1,420 kg/m³ against 2,670 kg/m³ for DMLS AlSi10Mg Aluminum.
Which is stiffer, DMLS AlSi10Mg Aluminum or Plastic POM/Acetal?
DMLS AlSi10Mg Aluminum is stiffer: Young's modulus 72 GPa against 2.8 GPa for Plastic POM/Acetal, so the same part in DMLS AlSi10Mg Aluminum deflects less under the same load.
Which is lighter for the same job, DMLS AlSi10Mg Aluminum or Plastic POM/Acetal?
For the same stiffness or strength: DMLS AlSi10Mg Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
| Part that must be | DMLS AlSi10Mg Aluminum | Plastic POM/Acetal |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 13.7x heavier |
| Stiff beam (bending) | lighter | 2.7x heavier |
| Stiff panel or plate | lighter | 1.57x heavier |
| Strong rod or tie | lighter | 2.08x heavier |
| Strong beam | lighter | 32% heavier |
| Strong panel or plate | lighter | 5% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS AlSi10Mg Aluminum or Plastic POM/Acetal?
Plastic POM/Acetal stretches further before it breaks: 75% elongation at break against 10.2% for DMLS AlSi10Mg Aluminum.
Thermal
Which conducts heat better, DMLS AlSi10Mg Aluminum or Plastic POM/Acetal?
DMLS AlSi10Mg Aluminum conducts heat better: 110 W/m·K against 0.4 W/m·K for Plastic POM/Acetal.
Which expands less with temperature?
DMLS AlSi10Mg Aluminum expands less: 20 µm/m·K against 122 µm/m·K for Plastic POM/Acetal.
Related comparisons
- DMLS AlSi10Mg Aluminum vs. Aluminum
- DMLS AlSi10Mg Aluminum vs. Aluminum 6061-T6
- DMLS AlSi10Mg Aluminum vs. Aluminum 2024-T351
- DMLS AlSi10Mg Aluminum vs. Aluminum 6063-T6
- Plastic POM/Acetal vs. SLA Resin Standard
- Plastic POM/Acetal vs. Plastic Polycarbonate
- Plastic POM/Acetal vs. Plastic PMMA
- Plastic POM/Acetal vs. Plastic Nylon