Materials / Compare
DMLS AlSi10Mg Aluminum vs. SLA Resin Standard
Compare DMLS AlSi10Mg Aluminum vs. SLA Resin Standard strength, stiffness, weight and thermal properties.
| Mechanical | DMLS AlSi10Mg Aluminum | SLA Resin Standard |
|---|---|---|
| Yield strength | 270MPa1 | not given (tensile used) |
| Ultimate tensile strength | 450MPa17.5x stronger | 60MPa2 |
| Flexural strength | not sourced | 105MPa2 |
| Elongation at break | 10.2%127% more ductile | 8%2 |
| Young's modulus (stiffness) | 72GPa326.2x stiffer | 2.75GPa2 |
| Density | 2,670kg/m³4 | 1,210kg/m³52.21x lighter |
| Strength to weight | 101kN·m/kg2.04x higher | 49.6kN·m/kg |
| Stiffness to weight | 27MN·m/kg11.9x higher | 2.27MN·m/kg |
| Poisson's ratio | base material0.336 | not sourced |
| Shear modulus | 27.1GPa | not sourced |
| Bulk modulus | 70.6GPa | not sourced |
| Speed of sound | 5,193m/s3.44x faster | 1,508m/s |
| Thermal | DMLS AlSi10Mg Aluminum | SLA Resin Standard |
|---|---|---|
| Thermal conductivity | 110W/m·K1204x more heat through a fin | 0.54W/m·K7 |
| Thermal expansion | mean 25-100 °C20µm/m·K15.71x less | mean -30 to 140 °C114µm/m·K7 |
| 100 mm part over a 50 °C swing | 100µm growth5.71x less | 571µm growth |
| Specific heat | base material963J/kg·K6 | 1,800J/kg·K7 |
| Heats up and cools (diffusivity) | 42.8mm²/s173x faster | 0.248mm²/s |
| Thermal shock resistance | 13,819W/m | not sourced |
| Max service temperature | not sourced | HDT 1.8 MPa59°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources7 documents: EOS GmbH, Formlabs, Renishaw, U.S. Department of Defense
- DMLS AlSi10Mg Aluminum
- EOS Aluminium AlSi10Mg (powder 9011-0024), EOS M 290 | 30 µm process (AlSi10Mg_FlexM291 2.01), as manufactured, horizontal; machined (turned) specimens, ISO 6892-1 B10
- SLA Resin Standard
- Formlabs Clear Resin V5 (FLGPCL05), TDS Rev. 01 March 20, 2024; printed on Form 4 at 100 µm, washed 5 min in >=99% IPA, post-cured 15 min at 60 °C in Form Cure. Orientation not stated.
- 1EOS Aluminium AlSi10Mg Material Data SheetEOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Yield strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Ultimate tensile strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Elongation at break: typical at break, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Thermal conductivity: typical, as manufactured, horizontal (ISO 22007-2)DMLS AlSi10Mg Aluminum · Thermal expansion: mean 25-100 °C, ASTM E228
- 2Clear Resin V5 Technical Data Sheet (2024)Formlabsarchived copySLA Resin Standard · Ultimate tensile strength: typicalSLA Resin Standard · Flexural strength: typicalSLA Resin Standard · Elongation at break: typicalSLA Resin Standard · Young's modulus (stiffness): typicalSLA Resin Standard · Max service temperature: HDT 1.8 MPa
- 3RenAM 500 Series Aluminium AlSi10Mg Material Data SheetRenishawDMLS AlSi10Mg Aluminum · Young's modulus (stiffness): same material and process, different machine maker: Renishaw RenAM 500, 30 µm, as built, horizontal (XY)
- 4EOS Aluminium AlSi10Mg Material Data Sheet, FlexLine, M 290 (2018)EOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Density: typical part density (ISO 3369), EOS M 290, AlSi10Mg_030_FlexM291 (30 µm)
- 5Clear Resin V5 Technical Data Sheet (web edition)FormlabsSLA Resin Standard · Density: typical, post-cured (same for 5 min ambient and 15 min at 60 °C), ASTM D792
- 6MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseDMLS AlSi10Mg Aluminum · Poisson's ratio: base material: cast Al-Si-Mg alloy 359.0 (Al-9Si-0.6Mg, closest MIL-HDBK-5J alloy to AlSi10Mg / EN AC-43000)DMLS AlSi10Mg Aluminum · Specific heat: base material: cast Al-Si-Mg alloy 359.0 (MIL-HDBK-5J), at 100 °C
- 7Thermal Properties of Selected Formlabs SLA ResinsFormlabsSLA Resin Standard · Thermal conductivity: typical, post-cured, ASTM E1530SLA Resin Standard · Thermal expansion: mean -30 to 140 °C, post-cured (5 min ambient cure), TMA ASTM E831SLA Resin Standard · Specific heat: typical, 25 °C, post-cured (5 min ambient cure), DSC ASTM E1269
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS AlSi10Mg Aluminum and SLA Resin Standard are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS AlSi10Mg Aluminum stronger than SLA Resin Standard?
DMLS AlSi10Mg Aluminum is stronger: its yield strength is 270 MPa against tensile strength 60 MPa for SLA Resin Standard (4.5x).
Which is lighter, DMLS AlSi10Mg Aluminum or SLA Resin Standard?
SLA Resin Standard is lighter: 1,210 kg/m³ against 2,670 kg/m³ for DMLS AlSi10Mg Aluminum.
Which is stiffer, DMLS AlSi10Mg Aluminum or SLA Resin Standard?
DMLS AlSi10Mg Aluminum is stiffer: Young's modulus 72 GPa against 2.75 GPa for SLA Resin Standard, so the same part in DMLS AlSi10Mg Aluminum deflects less under the same load.
Which is lighter for the same job, DMLS AlSi10Mg Aluminum or SLA Resin Standard?
For the same stiffness or strength: DMLS AlSi10Mg Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam; SLA Resin Standard is lighter for a strong panel or plate.
| Part that must be | DMLS AlSi10Mg Aluminum | SLA Resin Standard |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 11.9x heavier |
| Stiff beam (bending) | lighter | 2.32x heavier |
| Stiff panel or plate | lighter | 35% heavier |
| Strong rod or tie | lighter | 2.04x heavier |
| Strong beam | lighter | 24% heavier |
| Strong panel or plate | 4% heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS AlSi10Mg Aluminum or SLA Resin Standard?
DMLS AlSi10Mg Aluminum stretches further before it breaks: 10.2% elongation at break against 8% for SLA Resin Standard.
Thermal
Which conducts heat better, DMLS AlSi10Mg Aluminum or SLA Resin Standard?
DMLS AlSi10Mg Aluminum conducts heat better: 110 W/m·K against 0.54 W/m·K for SLA Resin Standard.
Which expands less with temperature?
DMLS AlSi10Mg Aluminum expands less: 20 µm/m·K against 114 µm/m·K for SLA Resin Standard.
Related comparisons
- DMLS AlSi10Mg Aluminum vs. Aluminum
- DMLS AlSi10Mg Aluminum vs. Aluminum 6061-T6
- DMLS AlSi10Mg Aluminum vs. Aluminum 2024-T351
- DMLS AlSi10Mg Aluminum vs. Aluminum 6063-T6
- SLA Resin Standard vs. Plastic Polycarbonate
- SLA Resin Standard vs. Plastic Nylon
- SLA Resin Standard vs. FDM Polycarbonate
- SLA Resin Standard vs. Plastic POM/Acetal