Materials / Compare
DMLS AlSi10Mg Aluminum vs. Stainless Steel 304
Compare DMLS AlSi10Mg Aluminum vs. Stainless Steel 304 strength, stiffness, weight and thermal properties.
| Mechanical | DMLS AlSi10Mg Aluminum | Stainless Steel 304 |
|---|---|---|
| Yield strength | 270MPa112% stronger | 241MPa2 |
| Ultimate tensile strength | 450MPa1 | 586MPa230% stronger |
| Elongation at break | 10.2%1 | 55%25.39x more ductile |
| Young's modulus (stiffness) | 72GPa3 | 193GPa22.68x stiffer |
| Density | 2,670kg/m³43.01x lighter | 8,030kg/m³2 |
| Strength to weight | 101kN·m/kg3.37x higher | 30kN·m/kg |
| Stiffness to weight | 27MN·m/kg12% higher | 24MN·m/kg |
| Poisson's ratio | base material0.335 | design value0.36 |
| Shear modulus | 27.1GPa | 74.2GPa2.74x stiffer in shear |
| Bulk modulus | 70.6GPa | 161GPa2.28x higher |
| Speed of sound | 5,193m/s6% faster | 4,903m/s |
| Thermal | DMLS AlSi10Mg Aluminum | Stainless Steel 304 |
|---|---|---|
| Thermal conductivity | 110W/m·K16.79x more heat through a fin | at 100 °C16.2W/m·K2 |
| Thermal expansion | mean 25-100 °C20µm/m·K1 | mean16.9µm/m·K218% less |
| 100 mm part over a 50 °C swing | 100µm growth | 84.5µm growth18% less |
| Specific heat | base material963J/kg·K5 | mean500J/kg·K2 |
| Heats up and cools (diffusivity) | 42.8mm²/s10.6x faster | 4.03mm²/s |
| Thermal shock resistance | 13,819W/m16.5x more resistant | 838W/m |
| Melting point | not sourced | melting range1,399–1,454°C2 |
| Max service temperature | not sourced | continuous899°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources6 documents: EOS GmbH, Cleveland-Cliffs, Renishaw, U.S. Department of Defense, Steel Construction Institute
- DMLS AlSi10Mg Aluminum
- EOS Aluminium AlSi10Mg (powder 9011-0024), EOS M 290 | 30 µm process (AlSi10Mg_FlexM291 2.01), as manufactured, horizontal; machined (turned) specimens, ISO 6892-1 B10
- Stainless Steel 304
- Type 304, annealed flat-rolled (Cleveland-Cliffs 304/304L Product Data Bulletin, May 2021); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
- 1EOS Aluminium AlSi10Mg Material Data SheetEOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Yield strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Ultimate tensile strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Elongation at break: typical at break, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Thermal conductivity: typical, as manufactured, horizontal (ISO 22007-2)DMLS AlSi10Mg Aluminum · Thermal expansion: mean 25-100 °C, ASTM E228
- 2304/304L Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 304 · Yield strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Ultimate tensile strength: typical, annealed, 70 °F (21 °C)Stainless Steel 304 · Elongation at break: typical, annealed, in 2 in. (50.8 mm)Stainless Steel 304 · Young's modulus (stiffness): typical, in tensionStainless Steel 304 · Density: typicalStainless Steel 304 · Thermal conductivity: at 100 °CStainless Steel 304 · Thermal expansion: mean, 0–100 °CStainless Steel 304 · Specific heat: mean, 0–100 °CStainless Steel 304 · Melting point: melting rangeStainless Steel 304 · Max service temperature: continuous, oxidation (scaling) limit in air
- 3RenAM 500 Series Aluminium AlSi10Mg Material Data SheetRenishawDMLS AlSi10Mg Aluminum · Young's modulus (stiffness): same material and process, different machine maker: Renishaw RenAM 500, 30 µm, as built, horizontal (XY)
- 4EOS Aluminium AlSi10Mg Material Data Sheet, FlexLine, M 290 (2018)EOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Density: typical part density (ISO 3369), EOS M 290, AlSi10Mg_030_FlexM291 (30 µm)
- 5MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseDMLS AlSi10Mg Aluminum · Poisson's ratio: base material: cast Al-Si-Mg alloy 359.0 (Al-9Si-0.6Mg, closest MIL-HDBK-5J alloy to AlSi10Mg / EN AC-43000)DMLS AlSi10Mg Aluminum · Specific heat: base material: cast Al-Si-Mg alloy 359.0 (MIL-HDBK-5J), at 100 °C
- 6Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 304 · Poisson's ratio: design value (structural stainless steels)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS AlSi10Mg Aluminum is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS AlSi10Mg Aluminum stronger than Stainless Steel 304?
DMLS AlSi10Mg Aluminum is stronger: its yield strength is 270 MPa against 241 MPa for Stainless Steel 304 (12%).
Which is lighter, DMLS AlSi10Mg Aluminum or Stainless Steel 304?
DMLS AlSi10Mg Aluminum is lighter: 2,670 kg/m³ against 8,030 kg/m³ for Stainless Steel 304.
Which is stiffer, DMLS AlSi10Mg Aluminum or Stainless Steel 304?
Stainless Steel 304 is stiffer: Young's modulus 193 GPa against 72 GPa for DMLS AlSi10Mg Aluminum, so the same part in Stainless Steel 304 deflects less under the same load.
Which is lighter for the same job, DMLS AlSi10Mg Aluminum or Stainless Steel 304?
For the same stiffness or strength: DMLS AlSi10Mg Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
| Part that must be | DMLS AlSi10Mg Aluminum | Stainless Steel 304 |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 12% heavier |
| Stiff beam (bending) | lighter | 1.84x heavier |
| Stiff panel or plate | lighter | 2.17x heavier |
| Strong rod or tie | lighter | 3.37x heavier |
| Strong beam | lighter | 3.24x heavier |
| Strong panel or plate | lighter | 3.18x heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS AlSi10Mg Aluminum or Stainless Steel 304?
Stainless Steel 304 stretches further before it breaks: 55% elongation at break against 10.2% for DMLS AlSi10Mg Aluminum.
Thermal
Which conducts heat better, DMLS AlSi10Mg Aluminum or Stainless Steel 304?
DMLS AlSi10Mg Aluminum conducts heat better: 110 W/m·K against 16.2 W/m·K for Stainless Steel 304.
Which expands less with temperature?
Stainless Steel 304 expands less: 16.9 µm/m·K against 20 µm/m·K for DMLS AlSi10Mg Aluminum.
Related comparisons
- DMLS AlSi10Mg Aluminum vs. Aluminum
- DMLS AlSi10Mg Aluminum vs. Aluminum 6061-T6
- DMLS AlSi10Mg Aluminum vs. Aluminum 2024-T351
- DMLS AlSi10Mg Aluminum vs. Aluminum 6063-T6
- Stainless Steel 304 vs. Stainless Steel 316
- Stainless Steel 304 vs. Stainless Steel 303
- Stainless Steel 304 vs. Iron
- Stainless Steel 304 vs. Steel AISI 1018