Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Plastic PEEK
Victrex PEEK 450G (unreinforced, injection moulded), Victrex TDS rev. March 2026; Poisson from Victrex fluid-management flyer (2020-07)
1
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Plastic PEEK?
Plastic PEEK is stronger: its yield strength is 98 MPa against tensile strength 18.4 MPa for FDM HIPS (5.33x).
Which is lighter, FDM HIPS or Plastic PEEK?
FDM HIPS is lighter: 1,023 kg/m³ against 1,300 kg/m³ for Plastic PEEK.
Which is stiffer, FDM HIPS or Plastic PEEK?
Plastic PEEK is stiffer: Young's modulus 4 GPa against 1.59 GPa for FDM HIPS, so the same part in Plastic PEEK deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Plastic PEEK?
For the same stiffness or strength: Plastic PEEK is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
FDM HIPS
Plastic PEEK
Stiff rod or tie (tension)
1.98x heavier
lighter
Stiff beam (bending)
25% heavier
lighter
Stiff panel or plate
7% heavier
lighter
Strong rod or tie
4.19x heavier
lighter
Strong beam
2.4x heavier
lighter
Strong panel or plate
1.82x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Plastic PEEK?
Plastic PEEK stretches further before it breaks: 25% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Plastic PEEK?
Plastic PEEK conducts heat better: 0.29 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Plastic PEEK expands less: 55 µm/m·K against 80 µm/m·K for FDM HIPS.