Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseMagnesium AZ31B-H24 · Young's modulus (stiffness): typical (handbook physical constant)Magnesium AZ31B-H24 · Density: nominalMagnesium AZ31B-H24 · Poisson's ratio: typical (handbook physical constant)Magnesium AZ31B-H24 · Max service temperature: stated application limit
4
Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
5
Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Magnesium AZ31B-H24 stronger than Plastic Nylon?
Magnesium AZ31B-H24 is stronger: its yield strength is 220 MPa against 63.1 MPa for Plastic Nylon (3.49x).
Which is lighter, Magnesium AZ31B-H24 or Plastic Nylon?
Plastic Nylon is lighter: 1,140 kg/m³ against 1,769 kg/m³ for Magnesium AZ31B-H24.
Which is stiffer, Magnesium AZ31B-H24 or Plastic Nylon?
Magnesium AZ31B-H24 is stiffer: Young's modulus 44.8 GPa against 2.33 GPa for Plastic Nylon, so the same part in Magnesium AZ31B-H24 deflects less under the same load.
Which is lighter for the same job, Magnesium AZ31B-H24 or Plastic Nylon?
For the same stiffness or strength: Magnesium AZ31B-H24 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Magnesium AZ31B-H24
Plastic Nylon
Stiff rod or tie (tension)
lighter
12.4x heavier
Stiff beam (bending)
lighter
2.83x heavier
Stiff panel or plate
lighter
1.73x heavier
Strong rod or tie
lighter
2.25x heavier
Strong beam
lighter
48% heavier
Strong panel or plate
lighter
20% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Magnesium AZ31B-H24 or Plastic Nylon?
Magnesium AZ31B-H24 conducts heat better: 76.9 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Magnesium AZ31B-H24 expands less: 26.8 µm/m·K against 100 µm/m·K for Plastic Nylon.