Materials / Compare
Nickel Inconel 718 vs. Plastic Polycarbonate
Compare Nickel Inconel 718 vs. Plastic Polycarbonate strength, stiffness, weight and thermal properties.
| Mechanical | Nickel Inconel 718 | Plastic Polycarbonate |
|---|---|---|
| Yield strength | 1,207MPa118.6x stronger | 65MPa2 |
| Ultimate tensile strength | 1,389MPa1 | 65MPa2 |
| Flexural strength | not sourced | 97MPa2 |
| Elongation at break | 20%1 | 125%26.25x more ductile |
| Young's modulus (stiffness) | 200GPa183.3x stiffer | 2.4GPa2 |
| Density | 8,221kg/m³1 | 1,200kg/m³26.85x lighter |
| Strength to weight | 147kN·m/kg2.71x higher | 54.2kN·m/kg |
| Stiffness to weight | 24.3MN·m/kg12.2x higher | 2MN·m/kg |
| Poisson's ratio | 0.2941 | 0.383 |
| Shear modulus | 77.3GPa88.9x stiffer in shear | 0.87GPa |
| Bulk modulus | 162GPa48.5x higher | 3.33GPa |
| Speed of sound | 4,932m/s3.49x faster | 1,414m/s |
| Thermal | Nickel Inconel 718 | Plastic Polycarbonate |
|---|---|---|
| Thermal conductivity | 11.4W/m·K157x more heat through a fin | 0.2W/m·K2 |
| Thermal expansion | 13.2µm/m·K14.92x less | 65µm/m·K2 |
| 100 mm part over a 50 °C swing | 66µm growth4.92x less | 325µm growth |
| Specific heat | 435J/kg·K1 | 1,172J/kg·K42.69x higher |
| Heats up and cools (diffusivity) | 3.19mm²/s22.4x faster | 0.142mm²/s |
| Thermal shock resistance | 3,680W/m71.2x more resistant | 51.7W/m |
| Melting point | melting range1,260–1,336°C1 | not sourced |
| Glass transition | not sourced | 144°C2 |
| Max service temperature | 704°C1579 °C hotter | UL 746B RTI125°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources4 documents: Special Metals, Covestro, Bayer MaterialScience
- Nickel Inconel 718
- INCONEL alloy 718, standard grade, 1750 °F/1 hr anneal + 1325 °F/8 hr F.C. to 1150 °F aged; Special Metals bulletin SMC-045 typical values
- Plastic Polycarbonate
- Covestro Makrolon 2405 general-purpose PC (MVR 19), Covestro technical datasheet version 2026-09-28, typical values
- 1INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
- 2Makrolon 2405 Technical Data SheetCovestroPlastic Polycarbonate · Yield strength: typical, tensile yieldPlastic Polycarbonate · Ultimate tensile strength: typical, stress at breakPlastic Polycarbonate · Flexural strength: typical, flexural strengthPlastic Polycarbonate · Elongation at break: typical, strain at breakPlastic Polycarbonate · Young's modulus (stiffness): typicalPlastic Polycarbonate · Density: typicalPlastic Polycarbonate · Thermal conductivity: typical, through-plane, 23 CPlastic Polycarbonate · Thermal expansion: typical, 23-55 C, parallel and normalPlastic Polycarbonate · Glass transition: typical, DSC 10 C/minPlastic Polycarbonate · Max service temperature: UL 746B RTI, tensile strength, 1.5 mm
- 3Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroarchived copyPlastic Polycarbonate · Poisson's ratio: typical, polycarbonate family (Covestro Part and Mold Design guide, Table 3-1)
- 4Makrolon 2405 Data Sheet, ASTM valuesBayer MaterialSciencearchived copyPlastic Polycarbonate · Specific heat: typical (guide value), Bayer ASTM datasheet for Makrolon 2405, ASTM D 2766
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Nickel Inconel 718 stronger than Plastic Polycarbonate?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 65 MPa for Plastic Polycarbonate (18.6x).
Which is lighter, Nickel Inconel 718 or Plastic Polycarbonate?
Plastic Polycarbonate is lighter: 1,200 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, Nickel Inconel 718 or Plastic Polycarbonate?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 2.4 GPa for Plastic Polycarbonate, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Nickel Inconel 718 or Plastic Polycarbonate?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam; Plastic Polycarbonate is lighter for a stiff panel or plate, strong panel or plate.
| Part that must be | Nickel Inconel 718 | Plastic Polycarbonate |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 12.2x heavier |
| Stiff beam (bending) | lighter | 33% heavier |
| Stiff panel or plate | 1.57x heavier | lighter |
| Strong rod or tie | lighter | 2.71x heavier |
| Strong beam | lighter | 2% heavier |
| Strong panel or plate | 1.59x heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Nickel Inconel 718 or Plastic Polycarbonate?
Plastic Polycarbonate stretches further before it breaks: 125% elongation at break against 20% for Nickel Inconel 718.
Thermal
Which handles higher temperatures, Nickel Inconel 718 or Plastic Polycarbonate?
Nickel Inconel 718 does: 704 °C against 125 °C for Plastic Polycarbonate.
Which conducts heat better, Nickel Inconel 718 or Plastic Polycarbonate?
Nickel Inconel 718 conducts heat better: 11.4 W/m·K against 0.2 W/m·K for Plastic Polycarbonate.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 65 µm/m·K for Plastic Polycarbonate.
Related comparisons
- Nickel Inconel 718 vs. Stainless Steel 17-4PH
- Nickel Inconel 718 vs. Steel AISI 4340
- Nickel Inconel 718 vs. DMLS 17-4PH Stainless Steel
- Nickel Inconel 718 vs. Steel AISI 1045
- Plastic Polycarbonate vs. Plastic Nylon
- Plastic Polycarbonate vs. SLA Resin Standard
- Plastic Polycarbonate vs. FDM Polycarbonate
- Plastic Polycarbonate vs. Plastic POM/Acetal