Materials / Compare
Plastic Nylon vs. Stainless Steel 17-4PH
Compare Plastic Nylon vs. Stainless Steel 17-4PH strength, stiffness, weight and thermal properties.
| Mechanical | Plastic Nylon | Stainless Steel 17-4PH |
|---|---|---|
| Yield strength | 63.1MPa1 | 1,275MPa220.2x stronger |
| Ultimate tensile strength | 63.1MPa1 | 1,379MPa221.9x stronger |
| Flexural strength | 82.9MPa1 | not sourced |
| Elongation at break | not sourced | 9%2 |
| Young's modulus (stiffness) | 2.33GPa1 | H 900197GPa284.5x stiffer |
| Density | 1,140kg/m³16.84x lighter | H 9007,800kg/m³2 |
| Strength to weight | 55.4kN·m/kg | 163kN·m/kg2.95x higher |
| Stiffness to weight | 2.04MN·m/kg | 25.3MN·m/kg12.4x higher |
| Poisson's ratio | base material0.43 | H 9000.2722 |
| Shear modulus | 0.833GPa | 77.4GPa93x stiffer in shear |
| Bulk modulus | 3.89GPa | 144GPa37.1x higher |
| Speed of sound | 1,430m/s | 5,026m/s3.51x faster |
| Thermal | Plastic Nylon | Stainless Steel 17-4PH |
|---|---|---|
| Thermal conductivity | base material0.33W/m·K4 | at 149 °C17.9W/m·K254.2x more heat through a fin |
| Thermal expansion | base material98–102µm/m·K4 | mean10.8µm/m·K2 |
| 100 mm part over a 50 °C swing | 500µm growth | 54µm growth9.26x less |
| Specific heat | base material1,700J/kg·K43.7x higher | mean460J/kg·K2 |
| Heats up and cools (diffusivity) | 0.17mm²/s | 4.99mm²/s29.3x faster |
| Thermal shock resistance | 53.6W/m | 7,809W/m146x more resistant |
| Melting point | 188°C1 | not sourced |
| Glass transition | 55.1°C1 | not sourced |
| Max service temperature | HDT 0.455 MPa89.2°C1 | 316°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources4 documents: UltiMaker, Cleveland-Cliffs, Covestro, BASF
- Plastic Nylon
- Ultimaker Nylon, 3D-printed specimens, XY (flat), conditioned >=24 h at room temperature; Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v2.00, April 20, 2022.
- Stainless Steel 17-4PH
- Cleveland-Cliffs 17-4 PH, Condition H 900, sheet/strip, transverse (Product Data Bulletin, May 2021)
- 1Ultimaker Nylon Technical Data Sheet, v5.00UltiMakerarchived copyPlastic Nylon · Yield strength: typicalPlastic Nylon · Ultimate tensile strength: typical, peak stress (= stress at yield)Plastic Nylon · Flexural strength: typicalPlastic Nylon · Young's modulus (stiffness): typicalPlastic Nylon · Density: typicalPlastic Nylon · Melting point: typicalPlastic Nylon · Glass transition: typicalPlastic Nylon · Max service temperature: HDT 0.455 MPa (printed specimens)
- 217-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 17-4PH · Yield strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Ultimate tensile strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Elongation at break: typical, transverse, in 2 in. (50.8 mm)Stainless Steel 17-4PH · Young's modulus (stiffness): H 900Stainless Steel 17-4PH · Density: H 900Stainless Steel 17-4PH · Poisson's ratio: H 900 (column)Stainless Steel 17-4PH · Thermal conductivity: at 149 °C (300 °F), H 900Stainless Steel 17-4PH · Thermal expansion: mean, 21–93 °C (70–200 °F), H 900Stainless Steel 17-4PH · Specific heat: mean, 0–100 °C, H 900Stainless Steel 17-4PH · Max service temperature: strength-retention limit (not oxidation)
- 3Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
- 4Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic Nylon stronger than Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stronger: its yield strength is 1,275 MPa against 63.1 MPa for Plastic Nylon (20.2x).
Which is lighter, Plastic Nylon or Stainless Steel 17-4PH?
Plastic Nylon is lighter: 1,140 kg/m³ against 7,800 kg/m³ for Stainless Steel 17-4PH.
Which is stiffer, Plastic Nylon or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stiffer: Young's modulus 197 GPa against 2.33 GPa for Plastic Nylon, so the same part in Stainless Steel 17-4PH deflects less under the same load.
Which is lighter for the same job, Plastic Nylon or Stainless Steel 17-4PH?
For the same stiffness or strength: Plastic Nylon is lighter for a stiff panel or plate, strong panel or plate; Stainless Steel 17-4PH is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
| Part that must be | Plastic Nylon | Stainless Steel 17-4PH |
|---|---|---|
| Stiff rod or tie (tension) | 12.4x heavier | lighter |
| Stiff beam (bending) | 34% heavier | lighter |
| Stiff panel or plate | lighter | 1.56x heavier |
| Strong rod or tie | 2.95x heavier | lighter |
| Strong beam | 8% heavier | lighter |
| Strong panel or plate | lighter | 1.52x heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Plastic Nylon or Stainless Steel 17-4PH?
Stainless Steel 17-4PH conducts heat better: 17.9 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Stainless Steel 17-4PH expands less: 10.8 µm/m·K against 100 µm/m·K for Plastic Nylon.
Related comparisons
- Plastic Nylon vs. Plastic Polycarbonate
- Plastic Nylon vs. FDM Polycarbonate
- Plastic Nylon vs. SLA Resin Standard
- Plastic Nylon vs. Plastic POM/Acetal
- Stainless Steel 17-4PH vs. Nickel Inconel 718
- Stainless Steel 17-4PH vs. Steel AISI 4340
- Stainless Steel 17-4PH vs. DMLS 17-4PH Stainless Steel
- Stainless Steel 17-4PH vs. DMLS Ti-6Al-4V ELI Titanium